92 Results for "㈎ 뉴원더풀포커 ㉦ rgg799.top ㄽ 게이밍 노트 북 ㆊ 윌리엄힐사이트 ㉬ 온라인포커룸 ㅙ 고스돕홈페이지 ㄿ 리얼머니바둑이 ㆀ 빅뱅게임 ㉮ 백두산맞고"

Testing and Tuning the PID
Log from SMD reflow hotplate
for tuning i followed more or less the tutorial PID Without a PhD from Tim Wescott and the tutorial and video from PID Explained Team. first i just checked with low temperatures of 20..40°C as i went on and tested up to 260°C i noticed that...

Project A, kind of finished
Log from raspberry pi zero handheld computer
Well, I lied, because projects like this one are never actually finished. But let's say I'm not going to do any major rework from now. It took one more board revision and a little bit of coding to come up with final hardwareIn the meantime, I made some...

Breadboard VGA from TTL and SRAM
Details from Breadboard VGA from TTL and SRAM
This is a follow-up of my "Breadboard VGA from EEPROM" project that was covered here [hackaday.com] two weeks ago.The video shows the new circuit's first signs of life. It is not really stable yet, but definitely getting somewhere. Halfway the build...

DIY PWM Driver
Details from DIY PWM Driver
In this Project, I will show you how to make PWM Controller. I'm using the laminator for the toner transfer method. What things you will need: Copper - clad board (Dual Layer) Ferric Chloride (FeCl3) Acetone (Nail polish remover) Glossy Paper LASER...

220V TO 24V 15A PSU 750W DC MOTOR SPEED CONTROL
Details from 220V TO 24V 15A PSU 750W DC MOTOR SPEED CONTROL
Choise the PSU I use OLD COMPUTER PSU about 300w from china. I cut all the wire not necessary. Take the Necessary Component The first i use iron solder for take 2 big heatsink. We only use the heatsink, all transistor and mosfet we don't use after that,...

Soft BASS preamplifier using TL072
Details from Soft BASS preamplifier using TL072
Soft base with high treble settings is the need of every stereo system. And today I have TL072 jfet operational amplifier-based audio preamp. All the controls are running on a single two channel op amp IC. Simple RC filters are used for the bass and...

Talking To Tiles
Log from A Tile Based MacroPad
With tile construction set, we now have to calibrate the reading of tiles and establish a "protocol" for mapping tiles to macros. I'm using the same SS49E Linear Hall Effect Sensor that I did with the TMD-3 project so I know that the Analog...

SATA, DDR3, Verilog Visualizer and Other Stuff
Log from Nysa: FPGA Development Environment
SATA StatusAfter weeks of painful debugging. I have been able to read and write to the hard drive!I ran into an issue though... the speed at which I can communicate with my FPGA to/from my computer maxes out at about 16MBs and the hard drive reads/writes...

Display
Log from Apollo Guidance Computer
I started wiring up the Memory sub-system board and realized quickly that I needed the display board to show the state of the various registers. I first had to create a backplane to connect the boards into. The backplane carries all the signals...

Component research and selection
Log from Home-brew SMT Reflow Oven
The foundational base for this project required some sort of oven. From the design perspective, I needed an oven, preferably one with a good heat-up slope, a temperature sensor, a solid-state relay that was capable of handling “house-hold”...

One implementation : outdoor cam
Log from SauronPi - autonomous Raspi camera
I have not decided all the objectives of this project. However, in order to "get things done", i started a subproject : an outdoor, battery powered and wifi camera. This one is designed with a friend of mine who does birds pictures, and thus is meant...

6283 Single IC Stereo Audio Amplifier Board
Details from 6283 Single IC Stereo Audio Amplifier Board
➢Step descriptions:✦Step 1:-Like always,we have printed the circuit on photo paper, and press it with iron.✦Step 2:-Put it into the water and rub it softly, after this submerge it into ferric chloride, and shake it slowly around 15 to 50 mins.✦Step...

Please, GCC !
Log from PEAC Pisano with End-Around Carry algorithm
I get tired of fighting GCC's weird code generator that won't get a clue from my source code. I'm (still) using gcc6.4.1 (2017, I know) but I don't know how to make it understand basic things... This is critical at my level because any little performance...

My own Arduino Nano Microcontroller board
Details from My own Arduino Nano Microcontroller board
Here is my new Arduino Nano board, This looks better with C-type and one step above compatible drivers. I faced many problems in making the PCB, but I think PCBWay is the solution to all of them with their prototype PCB capabilities. And looks of the...

AIMOS
Details from AIMOS
These are parts of AIME's operating system that I am beginning to shoe-horn into a Raspberry Pi or more probably a few Zero's networked together inside a smaller and less sophisticated quadruped. AIME was 3.2GHz dual-core intel powered and a lot more...

|<
<
3
4
5
6
7
>
>|