27106 Results for "《 예약문의 OIO↗8489↗8306》선릉레깅스┛Еimportanceム강남레깅스룸레깅스룸ㅂheavenly 레깅스룸강남레깅스 강남레깅스룸⊥선릉레깅스ゥfiercelyり"

Wearable computer
Instructions from Wearable computer
Disassemble the primary unit of the video glasses, which now resembles a black plastic bar. You should end up with two boards connected by a thin-film ribbon cable, one of which is connected to another board (containing a USB-like plug) connected by...

Wearable computer
Instructions from Wearable computer
The board with the USB-like connector on it will be connected to the colored wires via surface-mount solder on top of vias. This is a really bad thing for the kind of torque you are likely to put on this connector board. So, desolder these wires using...

Wearable computer
Instructions from Wearable computer
Unscrew one of the threaded caps on the goggles and remove the clear plastic pane. (Your pair may have a silvered or coloured glass pane on top; if so, remove this as well but do not drill into it -- discard it or keep it as backup for the other side.)In...

Wearable computer
Instructions from Wearable computer
Take a lens housing. Remove the lens and flip it over, then clip it to the other side of the housing. Put a thin layer of superglue along the edge of the lens housing (on the opposite side from the lens itself) and place it firmly atop the pane, on the...

Wearable computer
Instructions from Wearable computer
Take the glass pane (or if you don't have one, the other plastic pane) and trace it on some thin cardboard or paper, then cut it out. This will be a mask for blocking out light. Mark and cut out the places on this mask where the display will be. Cover...

Wearable computer
Instructions from Wearable computer
On the board containing the USB-like connector, on the edge opposite the connector whose wires you have resoldered, fold a piece of velcro. Connect the connector and then position a piece of velcro of the opposite type on top of your mask based on where...

Wearable computer
Instructions from Wearable computer
Disassemble the primary unit of the video glasses, which now resembles a black plastic bar. You should end up with two boards connected by a thin-film ribbon cable, one of which is connected to another board (containing a USB-like plug) connected by...

Wearable computer
Instructions from Wearable computer
On the raspberry pi, you may need to affix the battery pack to the pi. I recommend a rubber belt (of the variety used in small vacuum cleaners); however, several rubber bands will do.I recommend taking some foam and cutting a rectangular hole slightly...

Wearable computer
Instructions from Wearable computer
============= Instructions on haptic output coming soon ===========

Solid-state garduino with RTC & LCD!
Instructions from Solid-state garduino with RTC & LCD!
Take a 20 gallon storage tote. Using hot glue, fit mylar coated bubble wrap around the interior of the enclosure, and the interior of the cover.Cut insulation carefully to allow container to close easily.

Solid-state garduino with RTC & LCD!
Instructions from Solid-state garduino with RTC & LCD!
(These are the areas I wing it.)Get a board slightly larger than the footprint of your fluorescent lamp.Layout your junction boxes approximately how you'd like them to sit.

Solid-state garduino with RTC & LCD!
Instructions from Solid-state garduino with RTC & LCD!
When the junction box is roughly where you want it, collect a relay, and place it in the bottom of the junction box.Using self-drilling dry-wall screws, drill through the hole in the heat sink of the relay, through the junction box, and into the wood. ...

Solid-state garduino with RTC & LCD!
Instructions from Solid-state garduino with RTC & LCD!
If you can't safely wire 120VAC, please stop here. I bear no responsibility for any bodily injury, death, or loss of property as a result of mimicking this project.Wired 120VAC through the Solid State Relays, outlets, and switches shown in the schematic.Within...

Solid-state garduino with RTC & LCD!
Instructions from Solid-state garduino with RTC & LCD!
Apply Code to Arduino...

Light Emitting Ball (LEB)
Instructions from Light Emitting Ball (LEB)
Laser Cut Acrylic (2.6 mm thick I believe, but you can double check the slot measurements in the DXFs to be sure) Accordign to the following DXFs.https://drive.google.com/file/d/0B_2xkbzRozdxbHZLQ...Solder the ends of each ring of WS2811's together,...

|<
<
5
6
7
8
9
>
>|