27106 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸후기ð νeveningм셔츠룸후기선릉셔츠룸Ξthreshold 강남셔츠룸셔츠룸추천 셔츠룸후기シ셔츠룸후기㎩regular≡"

CASTLE | Home Automation Done Right
Instructions from CASTLE | Home Automation Done Right
Gather the parts and start prototyping the circuit on the breadboard. Set up the power and ground rails first, then build on up. BT Radio I/O goes to the corresponding I/O of the Arduino (invert the paths), the regular LED should go from a digital pin...

Put the plastic back on (optional)
Instructions from PewPew FeatherWing
If you are going to use the low-profile female headers on your Feather boards, you can put the plastic back on the pins, since they only need to stick out very little. If you are using regular headers, leave the plastic off, this way the pins can go...

Arduino Mystery Box
Instructions from Arduino Mystery Box
After gathering all needed items, you can wire them like I did in this Fritzing Diagram:For the NTC Thermistor I used a 10k resistor.For the Photoresistor I used a 5k resistor.You can use regular 220 ohm resistors for the LEDs.

Stitch the Fabric onto the Glove
Instructions from Snap Like You're Thanos!
I stitched all the sensor pads in with regular thread, and sewed some of the cabling as well. This helps with repeated bending of the solder joint. The sensor that is closest to your thumb is where your middle finger ends, while snapping.

Step 5
Instructions from Gameboy Clock
Screw the clock on the front case and pray that it still closes. I drilled holes in the clock battery holder and used as a washer them to hold everything in place, but regular washers should work as well. Be careful not screwing too hard, or the screws...

Add the encoder to the old power control knob
Instructions from Hacking a mircrowave
I soldered the encoder to the breadboard and made holes in it that match the regular holes in the housing of the microwave oven. Using brass spacers, I set the optimal height so that the handle does not stick out of the case.

High-voltage oscilloscope probe
Instructions from High-voltage oscilloscope probe
Add a capacitor across the output, to compensate the divider in a manner similar to the regular oscilloscope probe divider compensation. You need to try a number of capacitors, to obtain a good-looking square wave output. Make sure the connection between...

PCB /SMT MAKER LAB @ Home
Instructions from PCB /SMT MAKER LAB @ Home
Fabricating Single & Double Sided SMT PCBS.1) Stick the Toner transfer paper (TTF) onto a sheet of regular paper at the top edge for easy printer feed & crinkle free printing. I use painter's/masking tape for the job.When printing from EAGLECAD add a...

LED Matrix web controller
Instructions from LED Matrix web controller
StreamFor users to be able to see the LED matrix in realtime you need a regular webcam to stream it, i used the service http://bambuser.com/ using a very low resolution in order to have the less lag possible ( lag will always happen ), i managed to get...

Bike improvement: fitting a rack
Instructions from Bike improvement: fitting a rack
Go to the hardware store. For this project the following supplies were needed:2 x 50mm L-shaped mounting brackets1 x M6 screw, 40mm long1 x M6 washer1 x M6 locknut (it resists better to the vibrations than regular threaded nuts)2 x M5 locknuts (the rear...

LED Tree Jenkins Build Monitor
Instructions from LED Tree Jenkins Build Monitor
Cut a square piece of wood for the base. I used a scrap piece of 2x6 pine.Cut the corners at 45-degrees to create a regular octagon. This shape matches the size of my bottom ring pretty well.Drill a hole in the wood centered in the block approximately...

Mount Ball Head Mounts
Instructions from Solar Mirror Array
Place a regular 1/4" 20 nut on all bolts sticking out of the frame and then add a lock washer above the nut. I spun the nut down as far as it would go with my fingers. Screw on all the Ball head mounts on top of the bolts. They will vary slightly in...

Communication testing
Instructions from Link an old UPS to a QNAP NAS
This is a good time to test the linkage between your NAS and the Arduino.1. download attached BasicSerialTest.ino into the Arduino2. connect the Arduino to the NAS3. type the command (use your device port name from the previous step): screen...

Power supply
Instructions from Light-up LED Dress for Halloween
For the power regular I used a super overkill cheap 240W step down buck power supply I found on amazon. I wanted something fully enclosed, waterproof, low heat, for piece of mind against arcing or overheating. There is probably a much better...

Stepper motor and driver
Instructions from A Channel on RAMPS Shield over Arduino Uno
A trick this person found, is running a stepper motor with a driver board connected up without Arduinos or any computer. To do this is make a small circuit monostable 555 oscillator. Then output with a 10k resistor to “step”pin and motor...

|<
<
1
2
3
4
5
>
>|