27106 Results for "『 모든문의 OIO=5793=7458 』 선릉셔츠룸㈄『 모든문의 OIO=5793=7458 』 Ηcake²셔츠룸테란강남셔츠룸デwriter 셔츠룸테란강남셔츠룸 선릉셔츠룸⒁셔츠룸사이즈┲exhausted⅔"

Open Indirect Ophthalmoscope
Instructions from Open Indirect Ophthalmoscope
The step by step build instructions for "OIO" can be found here: http://www.instructables.com/id/Open-Indirect-Ophthalmoscope-OIO/

First test, part 2: Step through the videos
Instructions from PlayVideo: adaptive video player
When the system starts up the first video should start playing. Use the pushbutton or adaptive switch to step through all the videos. It should start back at the first video when the list is exhausted.

Music CD Ripper Robot
Instructions from Music CD Ripper Robot
Upon finishing a stack of disks, it's not so simple determining whether the stack of CDs is exhausted, the robot doesn't know. So it will fail several times opening the tray, trying to load a disk, closing the tray, etc.RobotRip detects error states...

Install the software
Instructions from PSION II Datapak and Rampak Reader/Writer
Upload software to the Arduino, and run the Python software on the PC. The Python software requires 4 libraries: serial, keyboard, time and os, you may need to install these first using pip (or conda if using the Anaconda distribution of Python). The...

Assess and Plan
Instructions from Electric Heart
Before you begin building this device, figure out what you're going to use it for. What voltages should it output? What current level? What will the variation be in the load you are driving? Is this going to be a general lab power supply, or are you...

Hardware requirements
Instructions from Building Visitor Management System - Waylay IO
For this tutorial, we have decided to use the M5Stack Ecosystem because it enables building such a system without prototyping specific tools, such as a soldering iron or prototyping cables. The brain of this project is the M5Core2, an IoT development...

Step 6: Demonstration
Instructions from Telescoping Pole Extension Sensing - Photoresistor
To demonstrate that the calibration was successful, we recorded a video and collected photoresistor readings while arbitrarily extending, retracting, and twisting the telescoping pole. The plot shares the output from the two photoresistors over time....

Wire Connections
Instructions from Building Visitor Management System - Waylay IO
Connect the Mini RFID Reader/Writer Unit to PORT A of the M5Core2 (the red port near the USB-C connector) using the Grove cable. This unit uses the I2C protocol to send data to the M5Core2.Take out the CORE2 plate on the back to expose the pins.The Finger...

Setting up Ameba to be I2C Master
Instructions from Communicate with Arduino UNO via I2C
Next, open another window of Arduino IDE, make sure to choose your Ameba development board in the IDE: “Tools” -> “Board”Then open the “Master Writer” example in “File” -> “Examples”...

Demonstration
Instructions from Strain Gauge Force Vector Sensing Pole
Turn on the Arduino recording and output, and collect the readings of interest from the strain gauges. In this example, we pressed the tip of the telescoping pole against a pumpkin on a chair to demonstrate the sensing principle. The force and direction...

Step 5: Demonstration
Instructions from EMT Conduit-Mounted Wind Sensors
The wind sensors, Arduino and EMT conduit telescoping mounting pole took measurements outdoors for about 90 seconds. The raw data, and processed wind speed and wind direction data are presented below. The method for converting from the raw Arduino readings...

Setting up Arduino Uno to be I2C Slave
Instructions from Communicate with Arduino UNO via I2C
In this example, we use Ameba as the I2C master writer, and use Arduino as the I2C slave receiver.When the I2C slave receives string sent from I2C master, it prints the received string. Setting up Arduino Uno to be I2C Slave First, select Arduino in...

Motion Alerts From Anywhere in the World
Instructions from Motion Alerts From Anywhere in the World
In this example, instead of adding a Digital Pin Writer Node, we are going to add an Interrupt Pin Reader Node. As the name suggests, this will monitor the signal pin on the PIR motion sensor and send the state on the Node's output pin. In this case,...

Conclusion
Instructions from Accuracy-Sensing Smart Sports Rebounder with ESP32
This proof of concept demonstrates that it's possible to track and log a soccer ball's landing position on a sports rebounder without using a webcam - instead, you can feed the output of several accelerometers into a trained recurrent neural network...

Sound Check
Instructions from Retrex Audio
This is the quick hack of another code sample "Register writer" to play a warm up sound. The hardware is based on the schematic linked in the code. Works with Arduino Uno R3 aka: 328 compatible boards. https://pastebin.com/raw/FehmVLQS /*******************************************************************...

1
2
3
4
5
>
>|