40 Results for "3D printing"

Project 3+Pi
Project by Tobius
6DoF stepper motor driver module PiHat or standalone feature. Optional closed loop 6DoF sensing available too.
- 43
- 34

3D Printed Ballscrew Linear Actuator
Project by Anthrobotics
Developing a cheap DIY alternative to expensive machined ballscrew actuators (with a little less precision). For humanoid robots.
- 831
- 4

"Spine" for 3+Pi
Project by Tobius
2 x 6DoF + 2 x 9DoF Sensor module(s) for 4 point reference in 3D space. Optional Accessory for 3+Pi board.
- 0
- 0

3D Printing
Log from Chronio
After designing the watch in Fusion360, I had to print the parts with a 3D printer, in my case the bq Prusa i3 Hephestos. As a material I am using PLA, mainly because it doesn't smell as bad as ABS. The main challenge was getting the case printed with...

3D Modeling
Instructions from Positivitypunk Backpack
My build started in Fusion 360. First modeling everything that needed to fit within the back and arranged them somewhat to fit tightly. I left room for a raspberry pi, which I did not model because I measured the space between the components and found...

HACKLET 109 – COMPLEX 3D PRINTED PROJECTS
Log from Hackaday.io Project
If you can’t tell, we’re on a roll with 3D printers and printed projects this month. So far, we’ve covered printers, andsimple functional 3D prints. This week we’re taking a look at some of the awesome complex 3D printed projects on Hackaday.io.Complex...

Kinetic Walker
Project by Kate Reed
The walker that walks with you, reducing common back problems by alleviating the need to lift and place a walking aid in front of you.
- 20
- 16

Posture Correcting Device
Project by Krishna Mohan
Long work from home hours, ignoring back/spine gives rise to back pain. This project is about a device which helps coping up that pain.
- 3
- 4

Elysium Max Exoskeleton
Project by Val
Exoskeleton suit replica from the movie Elysium in Autodesk Inventor, 3D printed and investment cast out of Aluminum
- 212
- 80

From paper to plastic
Log from Quadruped robot with 22 DoF
… or more correctly, from CAD to reality, as it is time for 3D printing! Initially, before getting my own 3D printer, I used Shapeways to print copies of some of the Robotis plastic brackets (they were hard to source online). At one point I also calculated...

Completed assembly instructions
Log from Elysium Max Exoskeleton
The first iteration of assembly instructions is here:https://github.com/01binary/elysium-max-exoskeleton/raw/master/instructions/assembly instructions.pdfI had to grow the scope several times but some important features made it into this release:Setup...

3X0 - 3D Printable exoskeleton concept
Details from 3X0 - 3D Printable exoskeleton concept
Measurements & design approach There are different ways of taking proper measurements before modeling the parts, the important is to avoid as much as possible to go by "trial-and-error" because well, no one wants to waste material and time when 3D printing....

Chassis assembled
Log from Quadruped robot with 22 DoF
After 3D printing a few more plastic parts and cutting all the aluminium plates, the custom chassis was finally complete! Below are some notes on the remaining 3D parts and the metal plates. More 3D printed parts and painting I printed off some of the...

Project Log 18: Let's design the bones!
Log from DIY Mech/Exoskeleton suit.
Monday, 13:38, 26/12/2022 I didn't had an idea for a Project Log 18 yet, but since I added so many off-topics on Project Log 17, my Hackaday website started to lag and I was afraid of resulting in the same problem/bug that happened in the Project...

Zvychai One
Details from Zvychai One
There were couple points in time when I was in need of: a purpose for a SBC i've had laying around;a platform to experiment with general purpose embedded system that ran Linux;a case to dip my toes into elaborate electronic box design in CAD of choice...

1
2
3
>
>|