1469 Results for "8-bit cpu"

Step 8: Drill Holes
Instructions from DIY PCB Etching
I used an electric drill to drill holes for the components. You can also use a manual PCB drill to do so. I also used a larger sized drill bit to drill holes for the mounting standoffs.

Brick layer 8
Instructions from RepKiln

Assembly Step 8
Instructions from E.R.N.I.E
To prevent the front wheels from falling off, use the short zip ties to tighten the wheels onto the motors. If you find that the wheels still fall off, remove the wheels, place hot glue into the hole and reattach them.

Step 8- Rear Frame
Instructions from Bellcycles: A New Take on the Bicycle
Lets finish up with the rear frame. Slide the triple trees onto the two .5" tubes and add the main 1 inch tube.

Airframe - Step 8
Instructions from MiniHawk VTOL
Test-fit each Motor Mount (Tilt Mount/Pod) with its respective completed nacelle. Sand or trim as needed such that the Motor Mount is able to tilt fully flush forward, and able to tilt up past 90 degrees of rotation. Nacelle Pocket Finishing

8. Field testing
Instructions from Elephant AI
Unfortunately, we have not been able to complete this testing in time for close of Hackaday Prize! But I'm sure once housing is completed, we can go ahead and do it! Some of the WWF researchers have offered to field test the prototypes, so I'm going...

Linkages/Components - Step 8
Instructions from MiniHawk VTOL
Form the elevon control rods by creating an L-bend 45mm from the threaded tip of the pair of 2-56 link rods used. Test fit the retaining Du-Bro E/Z Links 0.72 (2-56) Retainer Clip for each bend, and modify the bend as needed and cut flush. Alternatively,...

8: Configure tasmota software
Instructions from ESP and WS2812 based clock
Find the ip-adress of the esp. - this can probably be done in your routers status pages - or if you leave the esp in the programmer and boot it up while you are in a serial terminal it will show you its ip-adress Use a browser and go to the...

Electronics/Finishing - Step 8
Instructions from MiniHawk VTOL
The Center-of-Mass for the aircraft is intended to be at 165mm back from the tip of the nose, or 40mm back from the leading edge of the wing. This is exactly along the middle pair of mounting holes for the Battery Tray. This is an initial value, and...

#8 Assembly: feeder
Instructions from E-TKT: anachronic label maker
The feeder is a springed mechanism that helps the cog gain traction against the tape by gently denting the adhesive liner. Feeder + bearing surround 2x 623ZZ bearings with 2x washers, one on each extremity;slide them into the...

Step 8: The handle
Instructions from ⚡Thor's hammer⚡
There we started: a simple handle of 15 cm made of grey PLA by 3D printing. - second version: we then thought, that it could be nice to reproduce the "metal rings" of Thor's hammer. Then we thought: why not create those rings with real aluminium...

8. Clear access for PCB
Instructions from 6-Axis Micro Manipulator
Move the legs out to allow access for fitting the PCB to the frame.

Step 8: Open the GUI
Instructions from Power Analyzer based on a COTS Power Monitoring IC
If you have installed python3.9 or greater, you can just run pip install -r requirements.txt and then python3 main.py

Drill a 3/8" hole in the bottom.
Instructions from beer can microphones
This is for the guitar jack. Note: you don't have to put it in the bottom if you don't want. Also note: a conical bit works wonders for this as opposed to an increasing series of drill bits.

Step 8: Adding the Steppers
Instructions from OpenBraille Steam
The steppers are mounted to the board with the NEMA_support. The support has two holes for M3 screws. Screw the support into the stepper and insert the coupler into the shaft. I got the wrong kind of coupler so I had to put shrink tube for them to fit...

|<
<
1
2
3
4
5
>
>|