1314 Results for "X 올림피크 리옹 CDDC7닷컴 ㅿ프로모션번호 B77ㅿbepickڸ원엑스벳 슬롯머신ಣ서천복권방ṓ한화이글스오늘경기ୀ올림피크 리옹사랑 backpedal/"

Install outer cam arms into base
Instructions from KSP Controller Hardware
Parts required: 2 x M4 x 25mm socket head screws6 x M4 washers2 x M4 nyloc nuts1 x patience

Summary
Instructions from Grasp Bionic Hand
Assembly steps Printing and removing support material Fingers assembly Thumb assembly Inserting the motors on the palm Inserting the motor on the thumb Fingers and palm assembly Casting silicone in the molds Gluing the silicone “skin” in...

Supplies
Instructions from DIY $3 Single Chip Macro Keypad From Scratch
You will need the following supplies to make its macrokeyCustom PCB3D Printed base (for mounting the PCB at a tilted angle)4 M2 x 5 screwsCH552G E8051 Arduino IDE programmable MCUMode switchSMT buttonMini USB port7 x 0805 10k Ohm SMT resistors2 x 0805...

Android/RPi HDMI switch controller using RS232
Instructions from Android/RPi HDMI switch controller using RS232
On an Android device, install the SSH Button app. Configure it to run "sudo python ~/switch.py X" where X is the input you want to use.

Luggable PC
Instructions from Luggable PC
Install ATX motherboard1 x ATX motherboard with CPU, RAM, and port cover plate.6 x 6-32 screws

Luggable PC
Instructions from Luggable PC
Prepare M5 shoulder screw for assembly1 x M5 screw with shoulder 6mm diameter x 20mm length

robotic_arm
Instructions from robotic_arm
⦁ Take the wooden piece B (13cm x 4cm) and drill two holes of the dimension 22.2mm x 11mm along the length of the wooden piece separated by 70mm apart.

Example : Motor assembly
Instructions from Universal Speed Reducer
Components list : 1 x Motor Base1 x 7mm Ring4 x Screw M3 x 81 x Screw M2 x 3 Screw the four M3 x 8 2. Insert the 7mm ring on the shaft and screw the M2 x 3

Cumulus Wireless Sensor Platform
Instructions from Cumulus Wireless Sensor Platform
Solder the 3 x 220 Ohm Resistors (the 3 resistor spots nearest to the Crystal Oscillator)

Cumulus Wireless Sensor Platform
Instructions from Cumulus Wireless Sensor Platform
Solder 3 x 3mm LEDs (Top is Yellow, Bottom Left is Red, Bottom Right is Green)

Cumulus Wireless Sensor Platform
Instructions from Cumulus Wireless Sensor Platform
Connect the bottom-center + and - connection terminals to a 3V power source (CR3023 Battery, 2 x AA Battery, ..)

Single Chip AVR BASIC Computer
Instructions from Single Chip AVR BASIC Computer
Required Components:The component list for this computer is fairly low as only a single IC is required: 1 x ATmega 1284P Microcontroller 1 x DIL 40 Pin 0.6" IC Holder 1 x 40 Pin Female Pin Header (to be cut down into smaller headers) 1 x 16 MHz Crystal...

Luggable PC
Instructions from Luggable PC
Install LCD driver boards1 x HDMI to LVDS conversion board to drive LCD panel.1 x voltage booster to drive fluorescent backlight1 x button board (not useful for us, but must be attached to driver board. I found this out the hard way and had to buy a...

Remove retaining clip
Instructions from P1 - Solenoid 3-way conversion
Lift the retaining C clip with an x-acto knife and pull it out.

3D Printing
Instructions from Wombatics Otto
3D Printing SettingLayer Height : 0.2mmOutline Shells : 3Fill : 10%Supports: No STL Files2 x OttoDIY_foot_v08.stl2 x OttoDIY_Leg_v08.stl1 x Wombatics Otto Body.stl1 x Wombatics Otto Head.stl

|<
<
3
4
5
6
7
>
>|