5826 Results for "X 올림피크 리옹 CDDC7닷컴 ㅿ프로모션번호 B77ㅿbepickڸ원엑스벳 슬롯머신ಣ서천복권방ṓ한화이글스오늘경기ୀ올림피크 리옹사랑 backpedal/"

X Axis in place.......
Log from XYZ Repeatable Platform
Well after several attempts at what I would call fancy wood work, I managed to get the anti backlash and drive hardware in place for the X axis. And by several attempts I mean I was get very impatient to try and finish the whole thing tonight, which...

Assembling X axis
Log from *NEW* DIY Multiplex Plywood CNC Router

MacOS X support
Log from Linear CCD module
It turned out to be very easy to get a working Otterly CCD CLI for MacOS X, as the operating system uses the same underlying tty-system as linux.It was literally just a matter of getting my hands on a Mac (that was the hard part) and setting up the proper...

moteus controller r4.x
Log from mjbots quad
I'm making progress bringing up the "production" version of the moteus controller, the r4.x series. This version is designed to be produced in medium volumes, and also resolves some of the annoyances I had in the r3.x series. Features:3 phase...

29.11.2020 - Voron Switchwire X-Axis, X-beam, X Linear Rail, XZ blocks
Log from Voron Switchwire 3D Printer
Voron Switchwire X-Axis, X-beam, X Linear Rail, XZ blocks - Component Voron Switchwire X-Axis, X-beam with Linear Rail and XZ blocks Voron Switchwire X-Axis, XZ block - Right Side Voron Switchwire X-Axis, XZ block - Left SideMy Voron Switchwire Components...

Internal Clock x Temperature
Log from Guri: Ignition Controller for Air Cooled Engines
Initially the internal calibrated RC oscillator was considered to be the main clock source for the circuit but according with the datasheet the frequency variation with the temperature is too high, specially on the operation range foreseen for the device...

V2.x watch
Log from Neopixel pocket watch
Next gen of this watch would have no wifi, use a small micro controller like a ATtiny 85, possibly add a RTC and small coin battery. Only use LiPo to drive the neopixel display.Should yield a "works all convention long" (3-4 days) run time as apposed...

Conservation X Labs
Log from Supplyframe DesignLab: 2020 Hackaday Prize
Conservation X Labs [Conservation] The Mission Conservation X Labs’ mission is to end the global extinction crisis through the democratization of science, mobilizing new talent to work on extinction and climate crises, and ultimately, delivering...

#5Khz x 12
Log from K3lso Quadruped
Yep we hit #5Khz for each motor reading data from 12 servos over 12 FD-can channels!

Raspberry PI X-PC
Log from The X-PC. Hackaday Prize 2022 Entry
As previously mentioned, I've been given lots of old laptops. Most have working motherboards and screens so they can be turned into X-PCs.But I've also got a load with dead motherboards, this means I've now got a lot of working laptop screens with...

X Y calculations
Log from Simple & Cheaper CNC Shaper
It looks like the XY calculations are quite easy. Its called forward kinematics and can be seen calculated here https://www.marginallyclever.com/2012/02/drawbot-overview/. Next I have to do interrupts on the encoder rotation to make sure I get every...

Day X + 1
Log from Speakers that look like snails
Success!Both speakers printed. They sounded pretty good without any equalisation, though around 10 kHz there's a little more harshness than desired. But that's nothing to do with the transmission lines. It's the drivers themselves. ...

X Axis Reboot
Log from Printrbot 'SuperSize Me" Mod
I beefed up the guide rails. Seems to handle the weight fine on 12mm rails, HOWEVER...A change in rails means a change in bearings. I don't have any 12mm linear bearings just kicking around, so I opted to print some. Printed in igus Tribo and PLA, I...

Underside of the X Platform
Log from Desktop CNC Mill
I was doing some maintenance the other day. I took the opportunity to photograph the underside of the X platform.

Rebuilding the X-axis
Log from Turning a Makibox into a PCB Mill
In my previous post, I realised that the 4mm steel rods weren’t going to cut it when milling – they had way too much play, so I promptly ordered two 200mm linear rails (for the X-axis), two 400mm linear rails (for the Y-axis) and...

|<
<
2
3
4
5
6
>
>|