465 Results for "e-ink"

Parts & Tools
Instructions from DIY Musical Bell
Electronic Components: 1x IC UM66T AliExpress1x 100Ω Resistor AliExpress1x 220Ω Resistor AliExpress4.7KΩ Resistor AliExpress1x BC547 Transistor AliExpress1x SPDT Slide Switch AliExpress1x 5mm LED AliExpress1x...

Step 1: Parts & Tools
Instructions from How to Make a Siren Generator
Components: 1x UM3561 AliExpress1x BC547 NPN Transistor AliExpress1x 220KΩ Resistor AliExpress2x 220Ω Resistor AliExpress1x 5mm LED AliExpress1x SPDT Slider Switch AliExpress1x SP3T Slider Switch AliExpress2x...

The Original Tweeting Trump Book
Instructions from The Original Tweeting Trump Book
@realDonaldTrump Latest Twitter Feed on Inky WHAT E-Ink Display. Latest @realDonaldTrump Tweet using Raspberry Pi B3+ and inkywHAT e-ink display Instructions Requirements For this project you will need: ● Raspberry Pi B3+● Pimoroni Inky...

Quick and Nasty Tube Power Supply
Instructions from Quick and Nasty Tube Power Supply
Now you can slip the remaining I laminations into the gaps left by the E laminations. Leaving the last few E's out will make it easier to do this. You can then complete it by sliding in the remaining E pieces, then the I's. It should be a snug fit.

Lint & Dog Hair Super Capacitor
Instructions from Lint & Dog Hair Super Capacitor
Test!

robotic_arm
Instructions from robotic_arm
⦁ Glue the propeller of servo motor of wooden piece A to the wooden piece E at any corner.

Optional components:
Instructions from Halloween talking clock based on Rpi Pico
3 pc step drill bit 3-20 mm + centerpunch shop now

Optional components:
Instructions from Motion activated talking critter based on Rpi Pico
3 pc step drill bit 3-20 mm + centerpunch shop now

Assembeling
Instructions from 3D printed BLDC servo with 30Nm torque ($60)

Part 2 - What we need
Instructions from NOOBIX IOT
Let's see all the needed parts and also check the schematic for this project below in order to know where to connect each part. We need the 220V to 12V regulator, the solid-state relay, an ESP32S smd version, some SMD capacitors and resistors, a diode,...

UV-badge
Instructions from UV-badge
Print mask & graphicsThe mask and graphics should be printed on the plexi cover. Use an appropriate printer, e.g. UV cured ink in special printer designed to print on solid objects. The graphics layer should be printed first, then the cover mask layer.Design...

Step 6: Iron the PCB
Instructions from DIY PCB Etching
Sand the PCB using a fine grit of sandpaper and some water. Place the image directly upon the copper side of the PCB and iron it for approximately 10 minutes. By doing so the laser printed ink will get transferred from the photo paper to the surface...

Find a suitable printer.
Instructions from Cheap inkjet printing for hackerspace
First thing you want to do is find a suitable printer. Generally it will be a slightly older model, and you will want it to be for a few reasons. 1.) The ink "security/drm" will likely be defeated 2.) There will be support from these CISS kits for them...

Make sure the suitable printer works!
Instructions from Cheap inkjet printing for hackerspace
I can't stress this one enough, make sure the printer actually works prior to you modifying it. If it's new in box and never has had ink within it might be the only time to ignore that. If the printer has been used, make sure using whatever means necessary...

Step 1: Parts & Materials
Instructions from DIY PCB Etching
Copper Clad PCB - AliExpressFerric Chloride Etching SolutionPCB Drill + Bits - AliExpressSandpaperPaper CutterPermanent MarkerLaser Printer

|<
<
2
3
4
5
6
>
>|