1471 Results for "solder fume extractor"

Discrete 741 operational amplifier in DIL8
Details from Discrete 741 operational amplifier in DIL8
I don't have time to make it myself, so I want to make it a kind of competition. The big challenge is that mounting the components has to be done by hand and with my solder paste dispenser: https://www.avdweb.nl/tech-tips/solder-paste-dispenser It's...

Skywatcher neq5 USB power
Details from Skywatcher neq5 USB power
The quick and dirty way to add USB power to the mount is simply to solder the + and - lanes of an USB cable to the + and - wires coming out of the battery pack.

World Create Day @OlyMEGA
Details from World Create Day @OlyMEGA
Come over to OlyMEGA after Marching for Science and make something cool. We will have a few learn to solder stations and the makerspace will be open to the public.

One Handed Manual Solder Feeder
Details from One Handed Manual Solder Feeder
After a few iterations, here was my design for a manual one handed solder feeding assistive device. A 3d printed hollow tube forms the base and with a wire ferrule connection at the end for a metal blunt tip near the soldering iron. The body...

Retrofitting USB-C on any 3D Printer
Details from Retrofitting USB-C on any 3D Printer
Tools used: ►Solder Iron ►Solder ►Tweezers ►3D printed vice (helping hands would work just fine) ►Hand drill with 3mm drill bit ►Hex screwdriver 1.5mm and 3mm

Sunburn Monitor
Details from Sunburn Monitor
Some notes on building the board:I used 0805 passive parts. They aren't the smallest but they are much easier to place by hand than 0603.The MCU and SI1132 present a challenge to me as I don't want to do a solder stencil at the moment and the pads are...

Automatic street light without battery
Details from Automatic street light without battery
➢Step descriptions: ✦Step 1:-Prepare a BT136 triode. Its three pins are T1 T2 G. ✦Step 2:-Solder the 220K resistor to the pinT2. ✦Step 3:-Solder DB3 to the pin G. ✦Step 4:-Solder the 220K resistor together to DB3. ✦Step 5:-Solder the LDR photoresistors...

ESP-12 (ESP8266) Pogo Jig
Details from ESP-12 (ESP8266) Pogo Jig
BOM -2 x cheap "esp-12 adapter" white boards16 x pogo pinspin headersa piece of FR4 one-sided boarddouble-sided proto board (off the shelf part)kapton tapeSteps to create -First board:desolder the resistors on the bottom of the boardstick kapton tape...

Solder Paste dispenser
Details from Solder Paste dispenser
There are two types of dispensers. Not very DIY friendly air-pressure-controlled dispensers and motor-controlled dispensers. In this project I designed a Motorized dispenser which uses a screw to to convert the rotational motion into linear motion. Most...

Blink Coin cell toys collection
Details from Blink Coin cell toys collection
Check in store I want to teach kids about the technology we had before self-flashing LEDs :) It not using obviously self-flashing led but old good astable multivibrator. It is a nice piece of old fashion technology.1206 components are easy to solder...

Project Firebolt
Details from Project Firebolt
yo ho ho and three bottles of rum. we have problems with soldering. using weller 140/100 soldering guns, supposed to heat up and melt solder in 6 seconds. when the tips are fresh, this happens. later, the tips start...

Port City Makerspace Learn-to-Solder Badge
Details from Port City Makerspace Learn-to-Solder Badge
Assembly Instructions (Recommended, you can do in any order you wish) Front: Has a white sawblade Back: Has outlines of parts and a robot that says AW YEA Insert the brass pin through the front of the board, solder from the back of the board.Set the...

RGB LED Strip Controller Circuit
Details from RGB LED Strip Controller Circuit
➢Step descriptions: ✦Step 1:-Prepare all the part need in this videos: 8050 transistor X3, 220uF capacitor 8*10mm X3, 10k resistor 0.5W X3, RGB strip DC 12V X1 and Some wire jumpers ✦Step 2: -Solder all the transistors, capacitors and resistors...

DIY a LED Christmas Tree
Details from DIY a LED Christmas Tree
➢Step descriptions: ✦Step 1:-Let's start soldering. We solder the SMD resistors first. They are really too small. ✦Step 2:-Then we solder interface of the TransFLash , there are a lot of pins, so we apply tin on the solder joint first. ✦Step 3:-OK,...

IRM mini
Details from IRM mini
Easy extension Solder pads on 4 sides, with both IN and OUT, makes it easy to extend IRM mini into a larger piece of display, whether with wires or just solder them together, it's your choice.SourceThis board is also Open Source!https://gitlab.com/tamctec/irm-mini...

|<
<
1
2
3
4
5
>
>|