Since the baffle is not really visible in the assembled clock, it can be printed very quickly with large layer heights.  Kevin Osborn was able to get the print time down to 25 minutes using a 1mm nozzle   With the .4mm nozzle you can go up to .2mm layers.  The rule of thumb is to make the layer height no more than 1/2 nozzle width. You can go higher, but this tends to get layer separation (theoretically you could do 1x nozzle width layers).

Glue the velum to the font of the baffle and trim away excess velum

The faceplate is etched on the backside.  The black letters are to be etched and the red lines are cut. Take your time here.  You may need to slow the etching speed down or make more than one pass to remove all of the opaque material.  There are several choices on the material.  Black is by far the most popular but Inventables (see bill of materials) offers several color choices.  The mirrored acrylic also works well.  For a super glossy finish, use spray-painted acrylic with at least four coats of paint, the last coat being in black.  Let dry completely between layers.

Pre-requests: Install Arduino, Feather Huzzah dev env, adafruit IO account.

TLDR;

1. Download the code from GitHub.
2. Set sketchbook folder: KlokTHREEjr->arduino
3. Create libraries/credentials/credentials.h
4. Open arduino/DesKlok_IO/Desklok_IO.ino
5. Board: Feather Huzzah
6. Select port
7. Upload

Download the code from github.  You can either download the zip file or clone the repository.  The stable code for this clock is stored in DesKlok_IO.  The _IO in the name refers to the fact that we are using the Adafruit_IO library for controlling the clock. We will configure our IO controls after we upload the program to the Feather Huzzah.

Every WyoLum repository comes complete with all of the libraries you need installed in the “arduino/libraries” directory.  Point your arduino->preferences->sketchbook directory to your downloaded KlokTHREEjr/arduino/   (On my system it’s “/Users/justin/code/KlokTHREEjr/arduino”).

Next we need to put wifi and adafruit.io credentials into a file called credentials.h.  Open libraries/credentials/README and fill out your ssid, password and IO credentials.

#ifndef __CREDENTIALS_H
#define __CREDENTIALS_H
// Create a file called "credentials.h" that has ssid and pass as shown.
// This file should not be added to your public repository

char ssid[] = "YOUR_WIFI_SSID"; // your network SSID (name)
char pass[] = "YOUR_SSID_PASS"; // your network password
char* password = pass;

/************************* Adafruit.io Setup***************************/
#define IO_SERVER "io.adafruit.com"
#define IO_SERVERPORT 8883
#define IO_USERNAME "YOUR_IO_USERNAME"
#define IO_KEY "___YOUR_IO_KEY______" //copy paste AIO key

#endif

Finally restart Arduino.  If the path is set correctly, you will see a few Klok sample programs in the File->Sketchbook menu.  Open “DesKlok” from File->Skechbook->DesKlok.  Select the “Feather Huzzah” board from the Tools->Board menu.  Plug in your Feather Huzzah into an available USB port and select that port from the Tools->port menu in Arduino.  Finally upload the code.

Adafruit.io setup

IO allows us to leave off the tedious physical interface and go with a purely virtual interface.  To control the DesKlok, you will need to set up Adafruit.io.  You will need to create three feeds on io.adafruit: klok_brightness (0 to 50), klok_display_idx (0,1,2), and Timezone1 (-720 to 720),  klok_brightness. 

After you create the feeds, add dashboard to hold them. I used three slider-bars with the above limits.

Make sure you test the electronics before you assemble the clock.  Every time I build the clock without testing, I realize I forgot to solder the power jumper.

1. Prepare bus
2. Solder header and power jumper
3. Test
4. Final assembly

1. Prepare bus

The bus can hold one, two or three ultim8x8s.  Since we are using only two UlTiM8x8s, we need to remove some tabs from the bus as shown.

2. Solder headers and power jumper

Solder the female headers onto the bus board and the male headers to the Feather Huzzah.

Solder the included small switch to the bus or solder the center pad of the power jumper to the USB side.

3. Test

Plug the Feather Huzzah programed earlier into the bus.  Start arduino and open the serial monitor.  If all goes well (connect to wifi, and Adafruit IO) seconds will start ticking off.  

Once you see the time in the serial monitor, your LED panel should be lit (shown below with baffles and velum).

4. Final assembly.

What can go wrong?

• Forget to solder jumper switch
• Light leakage.– mask holes in ULTiM8x8
• Wrong ULTiM8x8 orientation (double check 5V and ground rails)

Use thin (1.66mm) m3 nuts to attach low profile screws to each of two ULTiM8x8 boards. Mask the holes around the edge to prevent light leakage. 

Attach bus board, paying close attention that the 5V and ground rails align with the LED panels.  Use 12 M3 nuts in the middle and 4 standoffs (20mm) in the corners. 

Attach the faceplate and backplates and you are done.  The space between the faceplate and backplate is exactly 30mm.  This can be filled a number of ways: 30mm standoff (preferred), 20mm standoff + 10mm spacer shown below (need longer M3 screws),  20mm and 10mm standoff (10mm standoffs come with ULTiM8x8).