1545 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

The Atomik Controller
Instructions from The Atomik Controller
Syncing and De-Syncing bulbsMore than one bulb can be synced to the same Device.1. Make sure power is turned off to the bulb(s) that you are going to Sync or De-Sync.2. On the Device page, after all the properties are filled in and saved, click the Sync...

Glowstick kinetics
Instructions from Glowstick kinetics
Build a linear CCD module (SPI-version)The 3D-printed CCD-box is for the LDO-version PCB (but the LDO part of the circuit does not necessarily need to be populated). Install a 1x6 pin header on the back of the board. [picture coming]Print everything...

Design
Instructions from The ULTIMATE Gumball Machine
As usual, almost everything that's more complex than making a few simple connections and a basic box needed a design in Fusion 360. I started out by sketching what I wanted the machine to look like. It needed to be tall, have enough room for all of the...

SET UP THE UNICORN: The Full Kit:
Instructions from The FUnicorn
Unpack the components from the box. You'll have everything above plus a Big Red Button Kit, a 9V battery and cable, and Arduino Shield and ISP headers. Set up the FUnicorn as in the Base Kit instructionsAssemble the Big Red Button Kit per its instructionsPlug...

Build the battery box & Aduino hosing
Instructions from Open Flow Meter
Download the wiring diagram from the files section.Solder the power wires to the bottom of the Arduino first. Then put the TFT display onto the Arduino.Put the housing side of the aviation connector into the housing and lock it in place with the screw...

Internet Connected NeoPixel Clock
Instructions from Internet Connected NeoPixel Clock
Neopixel clocks are pretty common, but I have done other clocks and had the basic NPT and DST change routines down already. Wanted to do a NeoPixel clock that used the black acrylic diffusion panel that makes the pixels look like they float...

3D print the mold
Instructions from Cheeky Frog Mask
Use the mold_all_compents 3mf file to print everything for a single mold. Printing without a brim works fine, 50% infill works for me. The pillars might cause some stringing, but this can be removed quite easily. To assemble push the pillars into...

Assembling the electronics
Instructions from Making an old Air Purifier smart
You can use the 3d printed mount bracket or you can also hot-glue the components in the air purifier cover. The 3d printed bracket consists of 2 parts: the mount plate and the electronics box. Mount the relays with 2.5mm screws and nuts, put the...

DIY MIDI FIGHTER
Instructions from DIY MIDI FIGHTER
Building the boxFirst of all we need to make an enclosure. I decided to make my own cause I didn't find any online. I made mine in oak. I recommend that you don't make the box too small so you can fit the components inside. My box is 16cm deep, 16cm...

MIDI IN circuit
Instructions from BeeTar - Wireless Rock Band Keytar
Cut a piece of perfboard down so it will fit into the little space between the screw post and keybed as shown in the image. I usually use a box cutter with a ruler as a straight edge to cut through perf - a few (careful) swipes and I can bend it and...

3DOF Hexapod (Hexapi)
Instructions from 3DOF Hexapod (Hexapi)
To hook up the ssc-32U to the PI, you will need a SparkFun Voltage Level Translator or something similar. The ssc has a logic level of 5 volts, the PI level is 3.3v. So you would hook the low side power/ground to the PI. For the ssc side, I only needed...

Lets do it
Instructions from Setup & Update the ESP8266 - Getting Started Guide
For communication to the module we are using Arduino IDE, it's simple and it has a Serial monitor. We first need to install the ESP board so the software recognizes our board (If you have not already installed Arduino IDE you can go HERE and install...

Adding an external relay for the second circuit (optional)
Instructions from Sonoff Mini dual switch support
If you happen to need another relay (or an electrical output for something else) for the new switch instead of just sending state changes over MQTT, you sure can, it's your device. To make it more convenient and reliable, we chose the GPIO1 with its...

Testing Our Light Hotspot
Instructions from Helium Light Hotspot with Dragino LPS8 DLOS8 Miner
As our Gateway is now configured to work as a Light Hotspot. We need to test if it is working fine or not, For that, we need to open the staging console from here. Once you have set up a device with a staging console, you need to copy things like Device...

Recreating Real-World Objects For 3D Printing
Instructions from Replacement Faceplate for Pyle PLMR24 Speakers
To get started, I had to take the old speakers apart and scan the original speaker box and the replacement speaker, face down, on a flat bed scanner at 300dpi. Those images were then imported into gimp and cropped to eliminate everything up to...

|<
<
1
2
3
4
5
>
>|