13109 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

Test again
Instructions from Personalized Theme Clock
Once the components are installed, test to ensure everything is working again.

Put the cover back on
Instructions from Personalized Theme Clock
Attach the cover and hopefully everything will fit inside your personalized clock.

Test fit
Instructions from Crystal RGB
Test if the crystal fits on top of your base. You may need to rearrange the wires to get everything to fit nicely.

Put everything into the photo frame
Instructions from Slow Movie Player 7C

Solder the front side
Instructions from LowPow E-Ink ShortKeyboard BLE, Wired, LoRa,Wifi
Start first with the ESP32 and the programming connector.Try to check with one led if everything is working.

Solar Powered USB Charger
Instructions from Solar Powered USB Charger
Connect everything up and verify everything works on a breadboard to power a Raspberry Pi.Image from "" target="_blank">ttp://www.polyideas.com/blog/2013/7/10/solar-powered-raspberry-pi>;

Bluetooth Headphone Mod
Instructions from Bluetooth Headphone Mod
After I got everything wired up, and modified the case to fit, I glued everything back together, and used shrink tube to hide the holes from the original earbuds.

Glue the generator parts together
Instructions from Propel-E 450 | A very powerful windturbine
Add glue to each part and press everything together firmly for half a minute. That should be enough to hold everything in place. Warning! Only glue the top 4 parts together, and the bottom 4 parts. Don't add top and bottom together yet because the stator...

KilnShark
Instructions from KilnShark
Wiring it up:Here is how everything is wired up:And a photo:I used a messy combination of soldering to header pins and jumper wires inserted into the breadboard. I also slightly overlapped the two boards to get everything to fit nicely.I used a rotary...

Time to solder everything!
Instructions from Meditation Audio Pod
If you're happy with the whole experience (i.e. wires are long enough, response time is good, speakers stay on for how long you want, etc) it's time to connect everything together! I find soldering a lot of fun so it's one of my favourite parts...

Trombino
Instructions from Trombino
Place the lid close to the bottom and wire everything in, trying to keep the wires short. There is very little clearance at the top of the case so anything attaching to the shield should not have extra height (eg no jumper cables!). After everything...

Putting LiPos into your MIP robot
Instructions from Putting LiPos into your MIP robot
Screw everything back together, and you've finished the MIP mods. Next, we make the battery packs. Pull out your LiPos. and cut the connectors off.. Careful not to short the leads. Connect the batteries in series, slide heatshrink on and then solder...

Resin-in-resin
Instructions from Resin-in-resin
PrepareGet a nice work area ready. You'll want plenty of space to assemble everything as well as paper towels and gloves -- epoxy is sticky! It's a step everyone wants to skip, but making sure you have everything laid out and ready to go will help you...

Trombino
Instructions from Trombino
Open up the Gametrak, unplug everything and remove one potentiometer and sliding tower block. (I forgot to take a picture of this, image from here: http://janoc.rd-h.com/archives/129)

Turn a cigarette lighter into an IR Nikon remote
Instructions from Turn a cigarette lighter into an IR Nikon remote
4.Wire everything as in the schematic diagram. The LED does not need a series resistor. Internal resistance of the cell batteries are doing a pretty good job in limiting the LED current.

|<
<
1
2
3
4
5
>
>|