Results for %E3%80%8A%EC%98%88%EC%95%BD%EB%B2%88%ED%98%B8OIOX8489X83O6%E3%80%8B%EA%B0%95%EB%82%A83hours%E2%94%903hoursrise%EA%B0%95%EB%82%A83hours%EA%B0%95%EB%82%A83hours3hoursbehaved 3hours %E3%89%B2%E3%8E%9B3hours%EB%A0%88%EA%B9%85%EC%8A%A4%EA%B0%80%EA%B2%A9each

Hacking a MG92b : Protect control bard
Instructions from Smarter Micro Servo (SMS) MOD
Use a a piece of heat-shrink sleeve as an envelop, or print a small 3D case to protect the control board.

Raspberry Pi Zero Smart Glass
Instructions from Raspberry Pi Zero Smart Glass
Next solder the ends of the smd buttons to the Pi Zero, and connect the camera cable to the Pi Zero

Raspberry Pi Zero Smart Glass
Instructions from Raspberry Pi Zero Smart Glass
Slide the Pi Zero through the PiHolder, with curved tweezers carefully guide the jst connecter and the camera cable through Buttonholder piece and the front bridge piece.

Trying out GATTTOOL
Instructions from Reading a bunch of BLE sensors with raspberryZero
Now that i know how to access and decode the data lets try the Raspi GATTTOOL default BLE handler:Native to Debian and a lso to a bunch of linux distros or so i've heard of . First i reset the bluetooth of the raspi, just in case: sudo service bluetooth...

Clone of stEve
Instructions from Clone of stEve
Mechanical assembly- Stepper motors into parts A1 & A2- Ends B1 & B2 slot into A1 & A2 to make a rectangle (B2 has no tabs, it goes in at the hook ends of A1 & A2)

Clone of stEve
Instructions from Clone of stEve
- A1,A2,B1,B2 assembly snaps into base C (line it up and pull the two spring clips back if necessary)- Tape a nut into slots on B1 & B2 (tape on one side should be enough to stop the nut falling out)

Create a function to decode the payload
Instructions from 2022 HDP 4 - Climate Resilient Communities
In order to decode the 23 bytes of payload that the sensor is sending we need to implement a decoder, in this case we need to create one custom. Once you select to create a custom decoder you just simply copy and paste the next code which is written...

NODE-RED CONNECTIONS!
Instructions from OBS_IRL_STREAM_DECK
The first thing we need is a basic flow to separate button presses into different outputs. [{"id":"50b49ab2.1e6f64","type":"mqtt in","z":"7805686.aa4fd98","name":"","topic":"button_glove","qos":"0","datatype":"auto","broker":"","x":310,"y":2180,"wires":[["ea9f502f.2dd17"]]},{"id":"ea9f502f.2dd17","type":"json","z":"7805686.aa4fd98","name":"","property":"payload","action":"obj","pretty":false,"x":490,"y":2180,"wires":[["425aef92.aa3da8"]]},{"id":"425aef92.aa3da8","type":"function","z":"7805686.aa4fd98","name":"ButtonSeperator","func":"var...

I2C Sensors and debugging
Instructions from Stratux ADSB Receiver and AHRS
I wanted to use a BMP280 I had in my parts bin for altitude measurements. I have used it in the past for a simple weather station and it works great! Turns out, it is even the go to sensor for Stratux, so I went ahead and plugged it in, activated it...

Instructions
Instructions from Budget DIY ESP32 GPS Base Station and Receiver
Best Budget DIY GPS/GNSS Base Station using the UM980 and a ESP32Introduction The ESP32 is a versatile microcontroller renowned for its WiFi and Bluetooth capabilities. In this guide, we’ll walk you through setting up the your ESP32 development board...

12V work light
Instructions from 12V work light
"U" frameMethod a) just use a vicemethod b) bend the shelf rail in three steps:b1) put the shelf rail on the table edge and firmly bend it to mark the locationb2) put the shelf rail on the floor, put a chair on top and sit on it, bend the shelf rail...

Rails
Instructions from Rave in a briefcase
I went for 2x3U. I screwed a piece of roofing battens into the case and the bottom rail directly onto them. The middle rails are just screwed together and are laid onto some standoff I laser cutted out of some scrap wood. The top rail...

Creating the L298n Circuit
Instructions from Volturnus ROV
The primary purpose of the circuit on our ROV is to take input from a program and use this input to control the motors. Obtain 2 L298n motor controllers.Connect the 12 volts and ground to the two terminals. Connect the 5 volts terminal to...

203 Results for "%E3%80%8A%EC%98%88%EC%95%BD%EB%B2%88%ED%98%B8OIOX8489X83O6%E3%80%8B%EA%B0%95%EB%82%A83hours%E2%94%903hoursrise%EA%B0%95%EB%82%A83hours%EA%B0%95%EB%82%A83hours3hoursbehaved 3hours %E3%89%B2%E3%8E%9B3hours%EB%A0%88%EA%B9%85%EC%8A%A4%EA%B0%80%EA%B2%A9each"