560 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸후기ð νeveningм셔츠룸후기선릉셔츠룸Ξthreshold 강남셔츠룸셔츠룸추천 셔츠룸후기シ셔츠룸후기㎩regular≡"

CAN BUS Gaming Simulator
Instructions from CAN BUS Gaming Simulator
Arduino Source Code://############################################################################################################## //Volkswagen CAN BUS Gaming //Test Sketch v3.0 //(C) by Leon Bataille 2015-2016 //Hackaday Project Page: https://hackaday.io/project/6288-volkswagen-can-bus-gaming...

3D Compass
Instructions from 3D Compass
Top Plate Assembly- Attach the magnetometer with 4-40 nylon screws. Shear the excess length flushwith the bottom of the plate using a hobby knife. Be careful to not breakthe superstructure on the printed part.- Place the capacitor into the cut-out and...

3D Compass
Instructions from 3D Compass
Wiring- Trim and solder the data-in wire on the vertical ring to the data-out padon the 24-element ring.- Connect the data-in pad on the 24-element horizontal ring to pin 13 on theArduino. The resistor goes in-line here as well. You can use 0.1" header...

Nano Bike Alarm
Instructions from Nano Bike Alarm
Software ConfigurationOnce you have the hardware complete, extract the package and open the 'newKey' sketch.In the Arduino IDE, edit this sketch and change the hex values for the newA and newB keys and for the tokenBlockData array. The keys are 6 bytes...

operation: Learn The MIPS (PIC32MX1xx/2xx/370)
Instructions from operation: Learn The MIPS (PIC32MX1xx/2xx/370)
Wire up your PIC32's MINIMUM requirements as-shown:(a summary of the related Project Log)(NOTE: If this page wraps-weirdly, try *shrinking* your window-width, counterintuitively)( '#' = MUST BE CONNECTED ) ( '*' = 5V-tolerant ) 3V3 ^ | \ / 10K PIC32...

operation: Learn The MIPS (PIC32MX1xx/2xx/370)
Instructions from operation: Learn The MIPS (PIC32MX1xx/2xx/370)
Wire the PIC32's JTAG pins to the FT2232H breakout-board/JTAGger:Pin Mapping: PIC32MX2xxFxxxB JTAG signal FT2232H (JTAGger) 14 TMS AD3 16 TDI AD1 17 TCK AD0 18 TDO AD2 (GND) (GND) (GND) (3V3) (3V3) (3V3) NOTE: I'm assuming you're taking 3V3 FROM the...

IBDAP - Affordable CMSIS-DAP JTAG/SWD Debug Probe
Instructions from IBDAP - Affordable CMSIS-DAP JTAG/SWD Debug Probe
OpenOCD Tutorialinstall depssudo apt-get install build-essentialsudo apt-get install autotools-dev autoconf automake libtoolsudo apt-get install texinfo libudev-dev libusb-1.0-0-dev libfox-1.6-devDownload FTDI driverhttp://www.intra2net.com/en/developer/libftdi/download.php...

SmartEE the Smart Plug
Instructions from SmartEE the Smart Plug
To initialize the plug with your wireless network SSID and password, plug it in and connect the USB plug to your computer. It should show up as a TTY serial interface (it enumerates as an ACM device). Use your favorite terminal emulator to connect. When...

Smart Power Sockets
Instructions from Smart Power Sockets
Connect RF module to Raspberry PI using a bread board and jumper wires.RF module’s power to Raspberry PI pin 2.(VDD -> 5V (#2))RF module’s ground to Raspberry PI pin 6(GND -> Ground (#6))RF modules data to Raspberry PI pin 16.(DATA -> GPIO23 (#16))

Smart Power Sockets
Instructions from Smart Power Sockets
Enjoy!

Up-Ride, the Bicycle to Elliptical Conversion Kit
Instructions from Up-Ride, the Bicycle to Elliptical Conversion Kit
Crank ExtensionProbably the trickiest element of this build.Crank face geometry is silly variable for aesthetic reasons. You may have to go for much thicker flat stock depending on your 3 piece crank (will not discuss 1 piece cranks here, if you want...

Kindle as a home automation controller/sensor
Instructions from Kindle as a home automation controller/sensor
Fit code to your network 1/2In read_fifo.c, I've hardcoded that when program see cvm[1234]: I SupplementarInfoBox:QUICK_LOOKUP:asin=51b5315f-77e9-4927-80b1-a9afbe1c4d76,word=Cuisine:it connects to http://mbp:8080/?toggle=CUISINEI provide with source...

Kindle as a home automation controller/sensor
Instructions from Kindle as a home automation controller/sensor
Fit code to your network 2/2Modify Docs/http_relay.py to change "mbp" :HOST_NAME = 'mbp'To the host of your computer. You can use IP either. And then start the "http relay" with python2 :kindle-home-automation/Docs $ python2 http_relay.py Server Starts...

DIY MIDI FIGHTER
Instructions from DIY MIDI FIGHTER
Building the boxFirst of all we need to make an enclosure. I decided to make my own cause I didn't find any online. I made mine in oak. I recommend that you don't make the box too small so you can fit the components inside. My box is 16cm deep, 16cm...

DIY MIDI FIGHTER
Instructions from DIY MIDI FIGHTER
Yay! You made it to the second step! In this step we will solder all the components and connect them to the Brain Jr.For this step you will need:A soldering ironSolderA wire stripper16 Arcade buttonsWires1. Strip the wiresStrip the wires.2. Put the buttons...

|<
<
3
4
5
6
7
>
>|