560 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》강남레깅스룸ⓨ강남레깅스룸singing강남레깅스강남레깅스룸강남레깅스룸remainder 강남레깅스㉮┢선릉레깅스agitation"

Arduino or Wemos Code
Instructions from WiFi Signal Strength Scanner Monitor or Checker
In the arduino code set your WiFi credentials char wifissid[] = "ENTER YOUR WiFi SSID HERE"; char wifipass[] = "ENTER YOUR WiFi PASSWORD HERE"; Normally, the signal strength is displayed in dBm. But for a non techie person, the signal strength in terms...

Cree Dimming Level
Instructions from Cree Dimming Level
Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...

DIY SlingBox $30
Instructions from DIY SlingBox $30
#!/bin/bash##recording1.shirsend SEND_ONCE --count=2 radioshack BTN_4irsend SEND_ONCE --count=2 radioshack BTN_6mencoder tv:// -tv driver=v4l2:norm=NTSC_M:width=720:height=480:outfmt=uyvy:device=/dev/video0:input=0:fps=25:buffersize=16:alsa:amode=1:forcechan=2:audiorate=48000:adevice=plughw.1,0:forceaudio:immediatemode=0...

Setting up Linux AVR and ARM toolchains
Instructions from Setting up Linux AVR and ARM toolchains
INSTALLING MINT ON A RELUCTANT TOSHIBA SATELLITE LAPTOPDownloaded the latest Linux Mint 16 with Mate image via torrent from linuxmint.org. Burned to DVD and used it to boot the Toshiba. All seemed to be going well untill the boot finished and I tried...

Getting started
Instructions from Projector Screen
Get and keep everything clean, including the back of your fabric. When you roll up the screen, the back touches the front, and any dirt will transfer right into the middle of your new screen. Take the actuator arm off the wiper motor. See what the threads...

The Dune Pain Box
Instructions from The Dune Pain Box
Winding the inductors is easier than you might think! I used about 4 feet of 18GA Magnet wire to wind the inductors for this particular power supply. Each inductor has ~30 turns on it for an inductance of about 90uH. If you don't have...

Animatronic AVP Predator cannon
Instructions from Animatronic AVP Predator cannon
Cannon code- #include "Servo.h" // include the servo library Servo armServo; // servo to raise the arm Servo cannonServo; // servo to recoil cannon // these constants won't change: const int triggerSensor = 1; // the sensor is connected to analog pin...

Jewel Box Servo Meter
Instructions from Jewel Box Servo Meter
Bend the pins on the header at a right angle. Drill 8 holes 1/16-inch (1.6mm) diameter in a line spaced 0.1-inch (2.54mm) on centers. Pass the pins through the holes with the header on the underside of the box.

Skype robot
Instructions from Skype robot
Build a robot with 1:16 RC tank platform and support the tablet with aluminum structure.tank

IRK! Infrared Remote USB Keyboard
Instructions from IRK! Infrared Remote USB Keyboard
Through Hole Technology (THT) versionThis is how I built the Through Hole Technology version Make a double-sided fibre glass PCB (see front- and back- PDF files below). There are several ways to do this. The way I do it is to print the front and back...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
Solder LEDs and diodes to sparkfun board, be mindful of their orientation.Thread the leads of 16 LEDs (5mm or 3mm are fine, I used 5mm) through LED holes in the Sparkfun PCB. These boards are compatible with 4-lead RGB LEDs, so there are four available...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
Two 74HC595s (wired in parallel) will be driving all the LEDs in the project as well as providing power to all of the buttons. The 74HC595 is an 8 bit serial in parallel out shift register. I've written a detailed tutorial about multiplexing with the...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
The 74HC595 can only do parallel output, so I used a 74HC165 to measure the state of the buttons via 4 current limiting resistors and send this information to the Arduino. More info about the chip can be found on its datasheet.The 74HC165 has the following...

Goliath - A Gas Powered Quadcopter
Instructions from Goliath - A Gas Powered Quadcopter
Mounting the EngineTools: 5/16" Wrenches and SocketsA) Prepare the Engine1) Check the wiring and redo the connectors2) Remove the excess choke hardware3) Remove the excess throttle hardwareB) Bolt the Engine to the FrameUsing (4) bolts, (4) lock washers...

Goliath - A Gas Powered Quadcopter
Instructions from Goliath - A Gas Powered Quadcopter
Building the ExhaustTools: Chop Saw or Reciprocating Saw, Files, Welder, Torx (T40) bit, Socket Wrench, 1/4" and 7/16" socketsA) Cut the materialsUsing the chop saw or reciprocating saw, cut the 1" diameter U-Turn and the 135 Bend, as well as the 1 1/8"...

1
2
3
4
5
>
>|