14060 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸후기た《〈 문의 OIO↗5793↗7458 》〉 ⑷plenty㎋셔츠룸후기셔츠룸후기んteeth 셔츠룸후기선릉셔츠룸 강남셔츠룸￦셔츠룸ⓤsilverⓞ"

Motor Upgrade
Instructions from Quad-ROS-bot
We decided that the standard motor on the QuadROSbot was not suitable for travelling over rough ground at slow speed - it was more suited to speed rather than torque. The motor chosen for the upgrade was a 3 phase 48 V DC motor with a 5:1 planetary gearbox...

Nautilus Twins
Instructions from Nautilus Sculptures
List of parts to be 3D printed and the required hardware components A 90 teeth spur gear. This would mate directly with the Nautilus gear.A compound gear with 30 teeth to mate with the 90 teeth gear to get the factor of 3 reduction in speed.A second...

Cut Out the Coroplast Rain Roof
Instructions from SASS-style Stereo Microphone for Nature Recording
Using the coroplast sheet (18x24) cut out the roof for the microphone. Dimensions are shown in the image below.By the way, the teeth marks in the template are from a black bear that chewed up a microphone.

Gearwheels assembly
Instructions from Universal Speed Reducer
Components list : 1 x Gearwheel 20 teeth1 x Gearwheel 19 teeth2 x Roller Bearing 8x22x76 x Screw M3x10 Insert the roller bearing in each gearwheel 2. Screw the six M3x10

Print parts
Instructions from Unpluginator
My motor already had a gear attached, but it was tiny and would have caused some issues with a normal 3d print. For the matching gear, I halved the extruded line thickness on the outer edge, to ensure tolerances were ok. Worked fine. For the remaining...

Mechanicals
Instructions from Basic Farm Robot 2021
In previous projects we spent a lot of time designing and building the mechanical systems and we really wanted to short cut all the hard work by using a ready made system that could be bought reasonably cheaply 'off the shelf'. We looked at mobility...

Pallette
Instructions from Pallette
http://website.palette.io.s3-website-us-east-1.amazonaws.com/imprint.htmlImprintWhat you will needMolded Mouthguard (from Step 3) Air-Dry Clay Medium Power Heat GunWith the molded mouthguard from Step 3, we'll make a clay imprint of your top teeth. This...

2. Build up levers
Instructions from 6-Axis Micro Manipulator
The levers and motor gears need to be printed using a high resolution method such as SLS nylon. This is because of the detail needed in the shape of the gear teeth (involute) that allows the set to move smoothly. Fit the PTFE bush into the pivot hole,...

Create a Custom Dental Impression - Alginate Negative Impression
Instructions from Intraoral Respiration Monitor & Overdose Detector
The respiration monitor electronics are built into a clear ultra-thin custom retainer. This retainer keeps the sensors and other electronics correctly positioned and also acts as a protective barrier between the electronics and the sensitive skin inside...

OPTIONAL Remove the Main PCB From the Internal Enclosure
Instructions from Hacking Wearables for Mental Health and More
The PCB test pads that you need to solder are on the exposed side the the PCB, but all those cool chips are on the hidden reverse side. If you are like me you will definitely want to take a look. Carefully push back the plastic teeth retaining the PCB....

Mounting the Button & LED
Instructions from Pentesting BBU Dropbox
Mount the LED where the "Wiring Fault" LED was and cover it in plenty of hot glue. Mount the push button with lots of hot glue where the "Reset" breaker button was.

Solarmodule preparation
Instructions from I<3T
Carefully put solar module on some soft underground so the front does not scratch. Then cut the long wire to around 50cm (see backside image as reference). Everything will be put in the back of the panel and there is plenty of room.

"Programming" sockets
Instructions from Trollduino V1.0
The sockets used to hold the 3 "programming" components R1, R2 and C are machined header pins stripped of their supporting plastic. An example of these can be seen here at Sparkfun, but these are available from plenty of other places too.

Install Arduino IDE with ESP32 support
Instructions from LORA for BRESSER 5 in1 Weather Station (MAKE IOT)
There are plenty of instructions out there: I cant explain it any better: https://randomnerdtutorials.com/installing-the-esp32-board-in-arduino-ide-windows-instructions/

Rotary Encoder Demo Board Wiring
Instructions from VCR Head Scroll Wheel (Imposter Syndrome Version)
The rotary encoder demo board was used in its default state, no changes required other than the jumper for 5VDC operation. The 5VDC supplied by the USB connection is plenty to power the magnetic rotary encoder.

1
2
3
4
5
>
>|