5943 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 쓰리아워ㅾ Йlife강남술집정보ħ쓰리아워레깅스룸강남쓰리아워７┢강남술집정보indignation 쓰리아워레깅스룸ケ쓰리아워ı㎃outside"

Mk 16 Capital Ship MDM
Instructions from Mk 16 Capital Ship MDM
Build Payload MPDB:1) 3D printed parts needed 1x MPDB 1a1x MPDB 1b1x MPDB 21) Cut Material: Cut 1" tubing to 212mmCut 3/8" tubing to 130mmCut 3/8" tubing to 30mm2) Construct Take 30 mm section of 3/8" tubing and place it into the center hole in...

J1772 Hydra
Instructions from J1772 Hydra
First, start by preparing the outer chassis. Remove and set aside the lid. Select one of the two short sides to be the top. This side will receive the button for the user interface. The opposite short side will receive either the cable gland for the...

Remote Controlled Weather Station
Instructions from Remote Controlled Weather Station
Today we'll be creating a remote controlled satellite weather station using a Raspberry Pi, a temperature sensor and a RockBLOCK. The envisioned application would be a weather station in a really remote location (i.e. outside of mobile/cellular coverage)...

Home Automation - Garage Door Opener
Instructions from Home Automation - Garage Door Opener
gdoPi.local - Python ScriptIf everything is working so far, you should be ready to test the relay/camera function via openHAB-triggered MQTT messages.Download the the ctrlGDO.py file and change ownership to 'pi':chown pi:pi ctrlGDO.pyEdit the file to...

BOB PID Servo Controller
Instructions from BOB PID Servo Controller
Pin onBOB LabelPIC PinPin on ENC1Encoder Signal1 or 6+5VCC55V2Y LEDRA03PhaseA3 or 4GNDGND4GND5 (not 4)Z LEDRA52PhaseBQuadrature Encoder:[ ] Install a 1x6 (or 1x5, pins 6 & 1 share +5) header over the holes for the Z and Y LEDs. (see picture) The polarity...

Part 6: Connect your charger to the outside world
Instructions from High Efficiency MPPT Solar Charger
There are only two mandatory connections: To the solar panel and to a battery. They are located at the top right of the board as part of the large 12-pin screw header. The labelling on the board is quite self-explanatory: Pan stands for panel....

Button Modifications
Instructions from Binary Wrist Watch
As you may have noticed the watch crown on the side of the watch is what you press to wake the watch from sleep. This crown had to be inserted into the body from the outside, should not be possible to accidentally pull out after assembled, and needs...

Unruly measurements: What does a return signal look like?
Instructions from Open Source LiDAR - Unruly
The yellow trace is the FIRE_N signal that triggers the laser driver circuit on the falling edge. The red trace (LeCroy has their own idea as to what red is) shows the return signal after the comparator. The time scale is 50 ns per division. The first...

Finding and modifying a suitable phone
Instructions from Less than $100, high FOV, mobile AR glasses
Required is a phone with a long flex cable leading to one of the cameras. In my research Chinese MIX smartphones are most suited. These have flex cables of ~10cm to the front camera (which is located at the bottom of the phone, instead of the top). You...

Assembling the PCB - Power
Instructions from GeoLeaf
For this step you will need: PCB Assembly5A (or greater) DC BarrelControl Base (3D Printed) The female barrel connector for our power supply is added into the 3D printed housing from the outside of the print and then secured with the included washer...

Configure Raspberry Pi for Waveshare monitor
Instructions from RUNBOX
In order to get the Waveshare to display properly you will need to edit the config.txt. To do so, open the terminal and type: sudo nano /boot/config.txt You will need to add the following: # 1920x1080 monitor (0 means monitor 1 the outside most hdmi...

I saw you move
Instructions from Squid Games Doll using Arduino UNO
The motion detector is a weird little guy. This thing uses infrared to detect movement. One thing I learned is that this sensor needs time to warm up. On startup it needs 1 minute to warm up. That is why there is a 1 minute startup time for the doll....

Main "module" assembly
Instructions from Open TEG Harvesting Module 2.0
Before getting started please find a spot to assemble the unit where you have a large flat surface and place something down on your surface to prevent a mess (the thermal compound and silicone sealant can get pretty messy.1. Apply thermal compound to...

Operation
Instructions from Halloween Mirror
Assemble all components in the frame in the correct order. With your frame assembled make sure the LDR is outside of the frame glued on the side. I replaced the back of my frame with a PLA plate with speaker holes. A guide to making easy speaker...

Build the Enclosure
Instructions from Seismometer
You need to enclose the seismometer to prevent air drafts and temperature variations from destroying the data. The sides of my enclosure are made from sandwiched layers of 1" thick insulation board, known as TUFF-R™. The board is covered on both sides...

|<
<
3
4
5
6
7
>
>|