Close

5943 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸ヒ 《〈 문의 OIO↗5793↗7458 》〉 ㎛beforehandム셔츠룸후기셔츠룸후기╇pen 선릉셔츠룸셔츠룸가격 셔츠룸‰강남셔츠룸㉦nestㅳ"

  • Assemble the stylus
  • Instructions     from Stylish!
  • Take an old pen and clean and hollow it. Get a non sharp, solderable bit of metal to use as the point. I used the tip of a 1/4" plug. Put your holes in your pen for the wire to get to the tip and thread the wire through. Solder the wire to the tip....

  • Hardware
  • Instructions     from CNC pen plotter
  • The assembly process is quite straightforward: Assembly the pulleys and pulley holders (3 in total).Assembly the pulleys, the motors and the motor holders (3 in total).Assembly the X shafts and the X shaft holders (2 in total).Assembly the movable left...

  • Frame
  • Instructions     from GRawler - Glass Roof cleaning crawler
  • Think beforehand how wide the crawler should be, or how wide the lanes are to move along. The length of the profiles and threaded rods depends on that, i use 700mm. Make sure that the profiles dip 1-2mm into the side panels Through the side panels and...

  • Wiring the matrix (columns)
  • Instructions     from FPGA Blinker
  • Now, solder 8 wires between C'x and G"x. Calculate the appropriate current limiting resistors values and have them handy (do the calcs and buy them beforehand). Solder the resistors on the borad and use wires to solder the PMOS drains (D'0, ..., D'7)...

  • Mount the desk automater and plug it in.
  • Instructions     from IKEA Bekant Desk Automater
  • Mount the device underneath your desk using wood screws. I used 16mm. You can use other lengths, just MEASURE BEFOREHAND SO YOU DON'T BREAK THROUGH THE TOP SURFACE... keeping in mind 3D printed plastic will compress as you tighten the screws. I recommend...

  • Mount the desk automater and plug it in.
  • Instructions     from IKEA Bekant Desk Automater
  • Mount the device underneath your desk using wood screws. I used 16mm. You can use other lengths, just MEASURE BEFOREHAND SO YOU DON'T BREAK THROUGH THE TOP SURFACE... keeping in mind 3D printed plastic will compress as you tighten the screws. I recommend...

  • Fix Up Down Arrangement
  • Instructions     from Cute Drawing Robot - Servo and Android
  • 1) Now the stand is ready. We want an arrangement to hold the servos and move up and down in the rail. 2) I use a old pen. Cut the pen in to two pieces and insert into the rods, The pen inner dia is more greater than the rod dia. So i insert a straw...

  • Mini Arduino CNC
  • Instructions     from Mini Arduino CNC
  • PARTS YOU NEED:For this project you will need: 3 x old CD/DVD-Roms 1 x Computer power supply 3 x Easydriver boards 1 x Arduino Uno board3 x Stepper motors2 x pieces of Wood1 x Soldering Iron1 x Soldering WireFew wires 1 x Pen or Small size drill machine...

  • PCB /SMT MAKER LAB @ Home
  • Instructions     from PCB /SMT MAKER LAB @ Home
  • Allow the board to cool a bit and then peel off the foil.The foil fills the pores in the thick toner areas, preventing pitting when etching. use your Xacto blade to check if the odd drill hole is also still covered by the foil, remove with the blade...

  • Attach the spring mechanism
  • Instructions     from Match Box ESP Dash Button
  • Use the insulated wire to form a spring (as shown above) by wrapping it around a round object, e.g. a pen. The diameter should be slightly larger then the spacing nut.Incidentally, the casing of the ESP is connected to GND, so we can just solder the...

  • Step 1: Part List to Prepare
  • Instructions     from Wall Drawing Robot, Open Source
  • Arduino Mega 2560 x 1pc CNC shield x 1pc Power supply PCB x 1pc SD card module x 1pc Stepper motor (traverse) x 2pcs Gear (for belt) x 2pcs Stepper motor (pen) x 1pc Belt x 2pcs Base x 1set Bolt, nuts (various) SoftwareArduino IDE/ Corel draw/ Microsoft...

  • Assemble the bow
  • Instructions     from Super simple foam cutter
  • Attach the baseboard to the frame with screws and wood glue. Assemble your bow (I don't have the bolts in the picture) Use the M6 bolt and wingnut and the M4 bolt and wingnut. The right-hand side of the bow (from the back) should be 93mm from the edge...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday