1008 Results for "강남권룸싸롱【θ1θ↔4⑥48↔0⑨30】xavi서울룸싸롱±선릉추천업소￡역삼풀싸롱ksubi강남룸접대paul서초풀싸롱σ강남추천업소θ선릉풀싸롱δ"

Controllers
Instructions from Thrifty Pick and Place
The controller that comes with the Elekslaser is the EleksMaker® ManaSE (version unclear) which is an arduino nano and supports two A4988 driver modules. I am using this to control the C axis and may use it's motor port - spindle speed - to control...

Sigma Derby Clone
Instructions from Sigma Derby Clone
Program the betting station)The betting station needs to know the odds of the current race to know what to pay out if you win. It also needs to know the race winner.Once again this is the fun version, so there is no code here for coin in, or cash out.#include...

Sigma Derby Clone
Instructions from Sigma Derby Clone
Program the horse boards to run the race that the mega sends it)As mentioned above, the finish board will send a 5 digit code for the next race the horses should run. Break out that information and run the appropriate race.#include Stepper motor(800,...

Sigma Derby Clone
Instructions from Sigma Derby Clone
Program the countdown clock)The countdown clock also needs to have the common ground, and pin 13 (the backlight) is hooked also connected to pin 2 on the start Mega switch board.#include LiquidCrystal counter(12,11,10,9,8,7); int count = 30; int count1...

Cuts required
Instructions from The Learner's Heliostat
The plywood product I used was 1/2x2x4 G1S, $37 ea before tax in Ontario in summer of 2022. For the project infrastructure, four 1" x 4" x 8' knotty pine planks would be price competitive and less work to waterproof, but less convenient to transport....

Leg Module
Instructions from Mike's Robot Dog
In one week, for less than $500., we can have a four leg module. To make the module stand and walk, power and control need to be provided and that will add about $100. more in cost (Arduino, battery, switches, voltmeter, wire, connectors). As shown in...

Arduino UNO Chess Clock
Instructions from Arduino UNO Chess Clock
Change the preset modes as you want static const GameType games[24] PROGMEM = { { FISCHER, 0, 1, {{ 300, 0}, {0, 0}, {0, 0}}}, // 01 Time blitz 5 min { FISCHER, 0, 1, {{1500, 0}, {0, 0}, {0, 0}}}, // 02 Time rapid 25 min { FISCHER, 0, 1, {{ 180, 0},...

Code for OLED Christmas Version
Instructions from Christmas Carol with OLED and Buzzer
#include "Wire.h" #include #include #define SCREEN_WIDTH 128 #define SCREEN_HEIGHT 32 Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, -1); #define LOGO_HEIGHT 4 #define LOGO_WIDTH 4 int frame_delay =800; const int NUMFLAKES = 1000; int8_t...

The Talking Microtronic Computer System Emulator
Instructions from The Talking Microtronic Computer System Emulator
Set up the hardware - the emulator main sketch shows the pin layout: // // SD+Ethernet Shield (optional) // #if defined (SDCARD) #define SDCARD_CHIP_SELECT 4 // // software serial interface for Emic 2 TTS module (optional) // #if defined (SPEECH) #define...

▇▇▇▇ Code Solution ▇▇▇▇
Instructions from FPGA Boot Camp #4: State Machines
There are many possible solutions, of course, but here's mine. Let's break it down into manageable pieces. First, let's look at the housekeeping items. I mentioned a 12 MHz clock, although that's ugly for simulation. Because of that, I wrote two...

3D Haptic Vest for Visually Impaired and Gamers
Instructions from 3D Haptic Vest for Visually Impaired and Gamers
Procedure for VestPurchase a Neoprene Vest.Put neoprene squares on 1" pieces of foam.Mount vibration motors on Neoprene platforms.Mount neoprene platforms onto the vest to be 2" apart in a grid pattern so that the vibrations can be recognized one from...

Wiring Instructions
Instructions from Braille Printer
1. Plug the 28BYJ-48 Stepper Motors in to the ULN2003 stepper Drivers. one will be used to roll the paper along the y-axis and one will be for moving the 'print head along the x axis. 2. Connect the x axis driver to the arduino from its pins...

Arduino Code Upload
Instructions from Quickly Build Arduino Smart Lamp
After installing the app, we are all done with the project. Upload the below Smart Light code to Arduino and enjoy the output using BT Remote pro app, as shown in the video. Here is the Arduino code for the Smart Light feature : //ARDUINO EXAMPLE CODE...

Python script to wait for a 3D fix and get the coordinates
Instructions from Raspberry PI wireless Telescope Control
I like to keep all the bash and python scripts at /home/pi/. So this time not working as root.Let's create a new file:nano get-gps.pyThis is the script:#!/usr/bin/env python import sys import time from gps3 import gps3 gpsd_socket = gps3.GPSDSocket()...

Affordable Reflectance Transformation Imaging Dome
Instructions from Affordable Reflectance Transformation Imaging Dome
Note: I've started converting these instructions into PDF format, and uploading them to my project Files section. These will ultimately be combined into a single large PDF file that will serve as a full manual for building and operating the system. The...

|<
<
1
2
3
4
5
>
>|