1008 Results for "강남권룸싸롱【θ1θ↔4⑥48↔0⑨30】xavi서울룸싸롱±선릉추천업소￡역삼풀싸롱ksubi강남룸접대paul서초풀싸롱σ강남추천업소θ선릉풀싸롱δ"

Step 4
Instructions from Elephant Holder
Use Scale tool with value 140 to stretch our model on axis X

Step 4
Instructions from DIY Decorative lamp | Home Decor Ideas
Switch back to Perspective mode Rotate molds by Y and X to 90

Step 4
Instructions from Easy Diy Pencil Holder
Scale the middle copy and set values: X: 195Y: 70 Z: 70 Select and isolate middle object from other objects

4. Assemble
Instructions from Dulles Clock
Make sure you test the electronics before you assemble the clock. Every time I build the clock without testing, I realize I forgot to solder the power jumper. Prepare busSolder header and power jumperTestFinal assembly 1. Prepare bus The bus can...

Step 4: PCB Fabrication
Instructions from How to Make a Siren Generator
Order PCB: PCBWay Eagle PCB Board Layout: GitHub Printable PDF: GitHub I fabricated the board using the Iron Method. I drilled four mounting holes in each corner with a diameter of 3mm. The PCB size is 3.3cm X 3.3cm .

Step 4: Source Code
Instructions from Arduino Color Picker
Source code is available for free on GitHub: https://github.com/alojzjakob/Arduino-Color-Picker You are more than welcome to improve the code, as the code provided is only the starting point, but works well. This project uses these 2 specific libraries,...

Step 4: Code
Instructions from Convert your old phone into a remote switch
Here I will read the analog port and look for a high signal. And switch the pins accordingly. I have written everything in comments and code is self-explanatory. Whenever it reads a certain voltage at analog pin it activates the switch. This switch can...

Step 4: The code
Instructions from Build Interactive Bridge Using Minecraft Raspi
We’ll start by writing our python code, first we’ll start by importing a few libraries that we’ll need in order to integrate our code with the Minecraft world. Then, we’ll import the time library, specifically a function called sleep. The sleep function...

Step 4: Code
Instructions from EMT Conduit-Mounted Wind Sensors
Because the wind sensors refresh their output approximately every 0.8 seconds, the Arduino Nano must measure those analog signals either slower or at that same rate. After taking those readings, the Arduino outputs them to a PC/laptop over Serial protocol...

3/4 plywood cuts.
Instructions from Simple bookcase
The 3/4 plywood has 5 cuts, All cuts a 12 inches wide. First two cuts trim the wood down to a 4x6ft board and the second 3 cuts take the boards down to four 12inch by 6ft boards. Here is a cut lines for the sides and...

4: make clock face
Instructions from ESP and WS2812 based clock
The clock face is made in plexi glass. Diameter 31.4cm (1m led strip / pi - 2 x 2mm thickness of led strip) The numbers was written on computer font size 96 and font size 120 for 12,3 ,6 and 9. I put the print out under the plexi glass and used...

Blynk App #4 - Joystick
Instructions from Wi-Fi Controlled Robot Using Blynk App
In this app I used a single joystick to control the robot. The speed of each track is defined deppending on x and y positions of the joystick. This way, it's possible to apply different speeds on each track, and move the robot with different speed/directions....

Step 4: Create Rectangles
Instructions from Design an 8 Bit Star Tree Topper in Fusion 360
Go to Sketch - Create Sketch and select the XY plane (red, green). Then choose Sketch - Rectangle - 2 Point Rectangle. We are going to use the rectangle tool to trace the first grid on the bottom left. Left click and release to place the...

Step 4: Arduino Connections
Instructions from Spider Robot with Arduino
Its time to make connections between Arduino and components. Please follow the instructions : front-left-axis : Pin 2front-left-lift : Pin 3back-left-axis : Pin 4back-left-lift : Pin 5back-right-axis : Pin 6back-right-lift : Pin 7front-right-axis : Pin...

Part 4: Powering on
Instructions from High Efficiency MPPT Solar Charger
When first powering on the charger, don't do so with a powerful battery or other powerful power supply. There's always a chance that there is a short circuit somewhere and connecting something like a car battery can immediately destroy your newly built...

1
2
3
4
5
>
>|