3734 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸후기た《〈 문의 OIO↗5793↗7458 》〉 ⑷plenty㎋셔츠룸후기셔츠룸후기んteeth 셔츠룸후기선릉셔츠룸 강남셔츠룸￦셔츠룸ⓤsilverⓞ"

Open Indirect Ophthalmoscope
Instructions from Open Indirect Ophthalmoscope
The step by step build instructions for "OIO" can be found here: http://www.instructables.com/id/Open-Indirect-Ophthalmoscope-OIO/

Motor Upgrade
Instructions from Quad-ROS-bot
We decided that the standard motor on the QuadROSbot was not suitable for travelling over rough ground at slow speed - it was more suited to speed rather than torque. The motor chosen for the upgrade was a 3 phase 48 V DC motor with a 5:1 planetary gearbox...

Mechanicals
Instructions from Basic Farm Robot 2021
In previous projects we spent a lot of time designing and building the mechanical systems and we really wanted to short cut all the hard work by using a ready made system that could be bought reasonably cheaply 'off the shelf'. We looked at mobility...

Pallette
Instructions from Pallette
http://website.palette.io.s3-website-us-east-1.amazonaws.com/imprint.htmlImprintWhat you will needMolded Mouthguard (from Step 3) Air-Dry Clay Medium Power Heat GunWith the molded mouthguard from Step 3, we'll make a clay imprint of your top teeth. This...

Robot Arm
Instructions from Robot Arm
Rotary Base Construction:Here is the rotary base. I machined a disk 8" in diameter and 1" thick from nylatron. I then cut out the internal shape and atached a Gates notched belt to the internal surface with Gorilla glue. The second 8"x8" nylatron blank...

Create a Custom Dental Impression - Bondo Positive Impression
Instructions from Intraoral Respiration Monitor & Overdose Detector
The fragile alginate negative impression is used as a mold to create a tough heat resistant positive impression. The positive impression will be used to form the specialized dental thermoplastic sheets into ultra-thin ultra-clear retainers. I use Bondo...

Linkages/Components - Step 4
Instructions from MiniHawk VTOL
For each of the Elevon servos, repeat the same procedure as above, but with a servo arm approximately 9.5mm hole-to-center (3/8 Inch). This length can be a bit longer or shorter, the effect is increasing or decreasing elevon control throw. For servos...

Nautilus Quintet
Instructions from Nautilus Sculptures
List of parts to be 3D printed and the required hardware components 5 Gear frame5 Nautilus gearsPegs to attach the gears to the frame608 BearingsActuator Assembly Instructions Mount the gears on the frame. Ensure that the teeth are meshed as shown...

Prepare X and Y motor supports
Instructions from BrailleRAP DIY Braille embosser
Screw together the parts XMOTOR_support2 and XMOTOR_support2_1 Fix a NEMA17 Motor in the X support with M3-8 screw Screw together the parts YMOTOR_support2_200_1, YMOTOR_support2_200_2, YMOTOR_support2_200 Fix the second NEMA 17 motor...

Attach Top to Stack Light
Instructions from Stack Light Monitor
Using a #2 phillips screw driver, remove the two mounting screws from the stack light. Fish the wire bundle through the large hole in the top enclosure piece. Use the two mounting screws to attach the top enclosure to the stack light.Trim...

Work Accent Lighting
Instructions from Work Accent Lighting
tl;dr; Open the LED strip controller from the bottomI got the LED strip off of Amazon and it seems like most of the strips use a very similar control module with an IR remote. A simple screwdriver is all it takes to pop off the bottom lid and inside...

The Tank Chassis
Instructions from WW2 Tank Laser Tag Game
DFRobot was generous enough to send me two of their MiniQ Robot chassis. The chassis have plenty of mounting holes that allow you to add brackets. They come with two motors and wheels, along with two sets of caster wheels to add strength. The assembly...

Step 8: Installing Personal Weather Station
Instructions from IoT Personal NodeMCU ESP12 WiFi Weather Station
The location weather station is the most important part of installation. If weather station is located under a tree or an overhang, the rainfall data measured by the station will not be correct. If you place your weather station in an alley, you could...

Step 2: Photo Editing
Instructions from Coin Card
I'm using GIMP, just because I have used it a few times. It is easy enough to get used to, especially when you can google just about anything you want to do on it. First, I need to decide which colours can be merged into one. I have 4 colours to work...

Assemble the motor mount and first stage
Instructions from Astrophotography Camera Mount
Set the motor mount retainer on top of the stepper motor and attach with 4 x M3 screws. Press-fit the 5 : 1 sun gear with the motor shaft axle to the stepper motor shaft. (note: the motor mount STL doesn't have the four holes in the plate right...

1
2
3
4
5
>
>|