445 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸후기た《〈 문의 OIO↗5793↗7458 》〉 ⑷plenty㎋셔츠룸후기셔츠룸후기んteeth 셔츠룸후기선릉셔츠룸 강남셔츠룸￦셔츠룸ⓤsilverⓞ"

Step 8: Installing Personal Weather Station
Instructions from IoT Personal NodeMCU ESP12 WiFi Weather Station
The location weather station is the most important part of installation. If weather station is located under a tree or an overhang, the rainfall data measured by the station will not be correct. If you place your weather station in an alley, you could...

Acrylic Tiles and Stand Assembly
Instructions from EnLIGHTen Web-Connected, OPEN source, LED Clock
After you apply the finish to the wood pieces, it's time to press in the acrylic tiles and assemble the stand. The acrylic tiles are press fit tolerances and don't require any adhesive generally speaking. A few of the tiles may need small amounts...

Hot Air Exhaust
Instructions from Nibbler Table Saw
The simplest of changes was to add a hot air exhaust port and duct. I chose Chardonnay because its oaky tones complemented the oak in the top. You can choose a nice red, just NOT MERLOT! This may look large, but I wanted to make plenty of room...

Building the Frame
Instructions from Seismometer
Cutoff two pieces of copper pipe 11" long, one 22", one 4 1/8", and two 1.5". Use a pipe cutter for this, it will make nice square edges.Drill a 1/4" hole through the center of the 4 1/8" piece for the eyebolt. Insert the 1.5" long pipe as connectors...

See what your going to make and the things you'll need:
Instructions from GeoLeaf
For those of you who prefer to watch something instead of reading I have created a detailed tutorial video. Don't worry though, everything in the video (and a little more) is all explained in this guide. Though, even if you will read through this guide...

Arduino GPRS IOT Weather Station
Instructions from Arduino GPRS IOT Weather Station
Arduino Soil Probe Using DS18B20 and DIY Moisture Hardware:As a fanatical gardener or a professional farmer, knowing the environmental conditions of our soil is invaluable. Obviously, we can't measure the number of worms or pieces of organic humus, but...

Building the AUV - Internal
Instructions from Project Albatross
The internals of the AUV performed the heavy work of actually taking water quality measurements and controlling the submersible's buoyancy. Evidently, it also required a sophisticated mechanical design to fit the necessary components into the confined...

IRK! Infrared Remote USB Keyboard
Instructions from IRK! Infrared Remote USB Keyboard
Through Hole Technology (THT) versionThis is how I built the Through Hole Technology version Make a double-sided fibre glass PCB (see front- and back- PDF files below). There are several ways to do this. The way I do it is to print the front and back...

A Measured Snow Shovel Improvment
Instructions from A Measured Snow Shovel Improvment
I used a work bench vise to hammer the old rivets down. Thought about using easier to get and use bolts, but they stuck out to much. Rivets work better and are easily replaceable if (when) they wear out.

Awesome Jacket
Instructions from Awesome Jacket
The kill switch was constructed using a short piece of 1.5" ABS plumbing tube and two end caps. Through one end cap I ran a multi-wire cord that carried 5V and the switch cct; to the other end I connected a stereo plug to match the jack described above....

The Dune Pain Box
Instructions from The Dune Pain Box
Winding the inductors is easier than you might think! I used about 4 feet of 18GA Magnet wire to wind the inductors for this particular power supply. Each inductor has ~30 turns on it for an inductance of about 90uH. If you don't have...

Low Cost CO2 Laser Build
Instructions from Low Cost CO2 Laser Build
Mirror Mounts0Mirror Mounts… where to begin, in many ways… these are the make or break it for this project. These have some very high tolerances and requirments. Especially considering I am doing this all by hand, after all, the goal of this project...

DIY Variac
Instructions from DIY Variac
After some looking around I got this one for 30 dollars.It was bare, but that is ok. I looked around for a container for it, and could not find one that I liked. I considered building one out of wood, but chose against that as well. One option was to...

Goliath - A Gas Powered Quadcopter
Instructions from Goliath - A Gas Powered Quadcopter
Mounting the EngineTools: 5/16" Wrenches and SocketsA) Prepare the Engine1) Check the wiring and redo the connectors2) Remove the excess choke hardware3) Remove the excess throttle hardwareB) Bolt the Engine to the FrameUsing (4) bolts, (4) lock washers...

Goliath - A Gas Powered Quadcopter
Instructions from Goliath - A Gas Powered Quadcopter
Building the ExhaustTools: Chop Saw or Reciprocating Saw, Files, Welder, Torx (T40) bit, Socket Wrench, 1/4" and 7/16" socketsA) Cut the materialsUsing the chop saw or reciprocating saw, cut the 1" diameter U-Turn and the 135 Bend, as well as the 1 1/8"...

1
2
3
4
5
>
>|