18945 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸후기た《〈 문의 OIO↗5793↗7458 》〉 ⑷plenty㎋셔츠룸후기셔츠룸후기んteeth 셔츠룸후기선릉셔츠룸 강남셔츠룸￦셔츠룸ⓤsilverⓞ"

Hacker and sheath
Instructions from Hacker and sheath
shape teeth with dremel and file

Attach teeth and solenoid
Instructions from Open Source Underwater Distributed Sensor Network
Silicone the teeth and solenoid to the shell (if they are not already printed on shell).

Body Wand Hack
Instructions from Body Wand Hack
Flash the ardunio with some simple code and Happy Teeth Rattling.

Track mover
Instructions from Track mover
Here is the second reduction gear assembly. The motor pinion has 13 teeth and the green nylatron has 72 teeth. This reduction is ~ 5.54. Total 5.54 X 2.88 = 15.9 : 1 .

Motor Upgrade
Instructions from Quad-ROS-bot
We decided that the standard motor on the QuadROSbot was not suitable for travelling over rough ground at slow speed - it was more suited to speed rather than torque. The motor chosen for the upgrade was a 3 phase 48 V DC motor with a 5:1 planetary gearbox...

Nautilus Twins
Instructions from Nautilus Sculptures
List of parts to be 3D printed and the required hardware components A 90 teeth spur gear. This would mate directly with the Nautilus gear.A compound gear with 30 teeth to mate with the 90 teeth gear to get the factor of 3 reduction in speed.A second...

Print shell, valve and other parts
Instructions from Open Source Underwater Distributed Sensor Network
Right now, the teeth and solenoids have not been integrated into the shell, so they must be printed separately and attached (I used silicone).

Build paper advance
Instructions from BrailleRAP DIY Braille embosser
insert the 360mm/8mm rod with a GT2 pulley 20 teeth, 3 paper roll with o-ring, and 200mm GT2 belt

Traffic Signal LED Matrix Display
Instructions from Traffic Signal LED Matrix Display
Mount all the back panel things to the back panel and add wires and connectors. 6 inch wires are plenty. Be careful about the polarity of the power jack and charge indicator LED.

Gearwheels assembly
Instructions from Universal Speed Reducer
Components list : 1 x Gearwheel 20 teeth1 x Gearwheel 19 teeth2 x Roller Bearing 8x22x76 x Screw M3x10 Insert the roller bearing in each gearwheel 2. Screw the six M3x10

Print parts
Instructions from Unpluginator
My motor already had a gear attached, but it was tiny and would have caused some issues with a normal 3d print. For the matching gear, I halved the extruded line thickness on the outer edge, to ensure tolerances were ok. Worked fine. For the remaining...

Pallette
Instructions from Pallette
http://website.palette.io.s3-website-us-east-1.amazonaws.com/mouthguard.htmlMouthguardWhat you will needSisu Mouthguard Fork Bowl Hot water MirrorTo begin assembling Pallette, you'll need to obtain the form of your top teeth. We'll use the mouthguard...

Installing the Ball End into the Jaw
Instructions from 3-Axis Skull Mod for 12ft Skeleton
Depending on the type of linkage you are using for the jaw, you will need to make a small hole near the back of the teeth for the linkage to attach. From here, test and adjust the linkage for the jaw to make sure you can close the jaw completely...

Mechanicals
Instructions from Basic Farm Robot 2021
In previous projects we spent a lot of time designing and building the mechanical systems and we really wanted to short cut all the hard work by using a ready made system that could be bought reasonably cheaply 'off the shelf'. We looked at mobility...

Pallette
Instructions from Pallette
http://website.palette.io.s3-website-us-east-1.amazonaws.com/imprint.htmlImprintWhat you will needMolded Mouthguard (from Step 3) Air-Dry Clay Medium Power Heat GunWith the molded mouthguard from Step 3, we'll make a clay imprint of your top teeth. This...

1
2
3
4
5
>
>|