Close

906 Results for "강남권룸싸롱【θ1θ↔4⑥48↔0⑨30】xavi서울룸싸롱±선릉추천업소￡역삼풀싸롱ksubi강남룸접대paul서초풀싸롱σ강남추천업소θ선릉풀싸롱δ"

  • Spectrum Analyser Code
  • Instructions     from Spectrum Analyser Code
  • SoftwareThe code can be downloaded from the project downloads page. But here it is:#include const static char ASCII[] PROGMEM = { 0x00, 0x00, 0x00, 0x00, 0x00, // 20 0x00, 0x00, 0x5f, 0x00, 0x00, // 21 ! 0x00, 0x07, 0x00, 0x07, 0x00, // 22 " 0x14, 0x7f,...

  • Cree Dimming Level
  • Instructions     from Cree Dimming Level
  • Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...

  • AIRee Pollution Clock
  • Instructions     from AIRee
  • #include #ifdef __AVR__ #include #endif // Which pin on the Arduino is connected to the NeoPixels? // On a Trinket or Gemma we suggest changing this to 1 #define PIN 6 // How many NeoPixels are attached to the Arduino? #define NUMPIXELS 48 // How much...

  • Source Code
  • Instructions     from Arduino Amazing Interactive Snowflake
  • #include "SoftPWM.h" #include byte edgeLedPins[] = {13, A4, A5, 2, 8, 12}; byte middleLedPins[] = {10, 6, 3, 5, 9, 11}; byte innerLedPins[] = {A2, A3, A1, 4, 7, A1}; ADCTouchSensor touchSensor = ADCTouchSensor(A0, 1); void setup() {   Serial.begin(115200);...

  • Final Test / Power Up
  • Instructions     from THB6064AH-SMT Stepper Motor driver
  • 13. [ ] Apply only the +5 volt power again, verify the power LED lights and nothing gets hot. 14. [ ] Power off, connect motor power (but don't turn it on!) and the motor. For help with sorting out the motor leads, see: Stepper...

  • Animatronic AVP Predator cannon

  • Instructions     from Animatronic AVP Predator cannon
  • Cannon code- #include "Servo.h" // include the servo library Servo armServo; // servo to raise the arm Servo cannonServo; // servo to recoil cannon // these constants won't change: const int triggerSensor = 1; // the sensor is connected to analog pin...

  • Daisy Kite Airborne Wind Turbine
  • Instructions     from Daisy Kite Airborne Wind Turbine
  • Respect the hard work and dedication to a better existence given by the open source community. Thanks must go to Grasshopper 3d algorithmic modeling language for rhinohttp://www.grasshopper3d.com/And Thanks now in no particular order to...David...

  • Program the Microcontroller
  • Instructions     from Fear the Scary Cat!
  • Before mounting the prototype PCB to the housing, I recommend uploading the required sketch to the ATtiny84 microcontroller with a programmer of your choice. I used a USBtinyISP type shown in the picture. /*Sketch for the Scary Cat Project by Gene H*/...

  • EDID Inserter
  • Instructions     from EDID Inserter
  • Plug in the freshly minted EDID Inserter and a repeated invocation of the following should yield only 256 FFs typical of an EEPROM fresh from the factory:sudo i2cdump 3 0x50Dire admonitions are issued even when merely trying to read:No size specified...

  • BASIC Code
  • Instructions     from Badge Modem
  • 5 a = 0 10 if a > 0 then goto 70 20 if a < 0 then goto 70 30 r = uin 0 40 chr r 50 a = kin 0 60 goto 10 70 uout a 75 a = 0 80 goto 10
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday