6690 Results for "『 모든문의 OIO=5793=7458 』 선릉셔츠룸㈄『 모든문의 OIO=5793=7458 』 Ηcake²셔츠룸테란강남셔츠룸デwriter 셔츠룸테란강남셔츠룸 선릉셔츠룸⒁셔츠룸사이즈┲exhausted⅔"

Mini Potato Cannon
Instructions from Mini Potato Cannon
3.) Push the hot paperclip through the pen tube about 1/4 inch from the end.

Mini Potato Cannon
Instructions from Mini Potato Cannon
4.) Shove the paperclip end of the tube into the hole in the bottle, until the paperclip is touching the bottle (but not inside it).

Mini Potato Cannon
Instructions from Mini Potato Cannon
7.) Poke 2 holes in the cap of the bottle about 1/4 inch apart, using another hot paperclip.

Paperclip Chainmaille
Instructions from Paperclip Chainmaille
1.) Straighten out a paperclip.

Paperclip Chainmaille
Instructions from Paperclip Chainmaille
2.) Wrap the paperclip very tightly around a small, 1/8 inch diameter rod or screwdriver.

Paperclip Chainmaille
Instructions from Paperclip Chainmaille
4.) Snip off each ring from the coil.

Make and Feel Virtual Drawings
Instructions from Make and Feel Virtual Drawings
Make Processing control Arduino THE FINAL PROGRAM:So,you have started drawing on Processing. Now, you'll 'feel' the drawing!Imagine you are blind (remember, this device was invented for blind people to draw on computers):How would you feel a raised line...

Make and Feel Virtual Drawings
Instructions from Make and Feel Virtual Drawings
Power to Servo motor So, we've written the code. Now start all wiring stuff:We have two options:Give 5V to servo motor from Arduino.Here, you can connect the servo motor ( attach a small fan to the motor ) to Arduino Uno. Servo motor has 3 wires: Connect...

Quick and Nasty Tube Power Supply
Instructions from Quick and Nasty Tube Power Supply
For this step you will want a variac or some way to limit the mains current. You might want to put a lamp in series with the hot wire to the transformer (are you sure you're comfortable working with mains electricity?)Connect everything up as you did...

Connecting 5V sensors to OpenWrt GPIO
Instructions from Connecting 5V sensors to OpenWrt GPIO
OpenWrt setupI use GPIO 29 so for input the setup looks like this:/etc/rc.local: # Put your custom commands here that should be executed once # the system init finished. By default this file does nothing. echo “29″ > /sys/class/gpio/export; echo...

Connecting 5V sensors to OpenWrt GPIO
Instructions from Connecting 5V sensors to OpenWrt GPIO
Output:And /etc/rc.local for output # Put your custom commands here that should be executed once # the system init finished. By default this file does nothing. echo “29″ > /sys/class/gpio/export; echo “out” > /sys/class/gpio/gpio29/direction...

Animatronic Iron Man MKIII suit
Instructions from Animatronic Iron Man MKIII suit
Notes about tools and materials used:ProPoxy 20 is awesome stuff. When making the brass tube pivots for the shoulder rocket pods it was easiest to glue the brass tube to the servo casing with superglue ( I use Gorilla glue with a spray accelerator) and...

Late Night Reading Lamp
Instructions from Late Night Reading Lamp
Solder LEDs, resistors etc onto a bit of veroboard. I used a female PCB header for plugging in the battery so that I didn't have to route long cables around the frame. Leave some length on the LED pins so that they stand up a bit from the veroboard

Jewel Box Servo Meter
Instructions from Jewel Box Servo Meter
Test fit all the components in the box to find the best arrangement. Cut a piece of strip board 8 rows wide and up to about 25mm long that will fit flat on the floor of the box. The strip board will act as a bus to connect to the header. I placed the...

Jewel Box Servo Meter
Instructions from Jewel Box Servo Meter
Bend the pins on the header at a right angle. Drill 8 holes 1/16-inch (1.6mm) diameter in a line spaced 0.1-inch (2.54mm) on centers. Pass the pins through the holes with the header on the underside of the box.

|<
<
3
4
5
6
7
>
>|