2002 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸ヒ《〈 문의 OIO↗5793↗7458 》〉㎛beforehandム셔츠룸후기셔츠룸후기╇pen 선릉셔츠룸셔츠룸가격 셔츠룸‰강남셔츠룸㉦nestㅳ"

Cumulus Wireless Sensor Platform
Instructions from Cumulus Wireless Sensor Platform
Connect the bottom-center + and - connection terminals to a 3V power source (CR3023 Battery, 2 x AA Battery, ..)

Getting started
Instructions from Projector Screen
Get and keep everything clean, including the back of your fabric. When you roll up the screen, the back touches the front, and any dirt will transfer right into the middle of your new screen. Take the actuator arm off the wiper motor. See what the threads...

Sci-fi grade Home Automation
Instructions from Sci-fi grade Home Automation
For the outlet power detectors:Cut the connectors off of your two wall warts and solder the grounds together (and to the ground on their Arduino)Solder the +5v wire of one wall wart to the +5v plug on the Spark core, and the other to digital input 3...

TI Launchpad Arcade Control to USB Interface
Instructions from TI Launchpad Arcade Control to USB Interface
Launchpad-Mame-Control TI Tiva C Launchpad firmware for Mame USB arcade controls adapterThis project is intended to design firmware for the TI Tiva C Launchpad development board to enable it to be used as a USB gamepad/mouse adapter for arcade and other...

Peril-Sensitive Sunglasses
Instructions from Peril-Sensitive Sunglasses
Accelerometer is wired like this:In my case I used:Analog 0 = X axisAnalog 1 = Y axisDigital 2 = 0g Detected

Back To The Future Time Circuit Clock
Instructions from Back To The Future Time Circuit Clock
Make sure you remove the LED from pin 13 from the Arduino on the Time Circuit Main board or your keypad won't work correctly.

The Dune Pain Box
Instructions from The Dune Pain Box
Winding the inductors is easier than you might think! I used about 4 feet of 18GA Magnet wire to wind the inductors for this particular power supply. Each inductor has ~30 turns on it for an inductance of about 90uH. If you don't have...

Animatronic AVP Predator cannon
Instructions from Animatronic AVP Predator cannon
Cannon code- #include "Servo.h" // include the servo library Servo armServo; // servo to raise the arm Servo cannonServo; // servo to recoil cannon // these constants won't change: const int triggerSensor = 1; // the sensor is connected to analog pin...

Make and Feel Virtual Drawings
Instructions from Make and Feel Virtual Drawings
Make Processing control Arduino THE FINAL PROGRAM:So,you have started drawing on Processing. Now, you'll 'feel' the drawing!Imagine you are blind (remember, this device was invented for blind people to draw on computers):How would you feel a raised line...

Jewel Box Servo Meter
Instructions from Jewel Box Servo Meter
Bend the pins on the header at a right angle. Drill 8 holes 1/16-inch (1.6mm) diameter in a line spaced 0.1-inch (2.54mm) on centers. Pass the pins through the holes with the header on the underside of the box.

ChipWhisperer®: Security Research
Instructions from ChipWhisperer®: Security Research
Optional (see #6 too, option of hard or soft enclosure): Use a 12" piece of 3" clear diameter heat shrink tubing to cover the board, the cut out the USB-mini connector with an X-acto knife, and mount rubber bumpers such as Digikey part # SJ5748-0-ND...

Skype robot
Instructions from Skype robot
Build a robot with 1:16 RC tank platform and support the tablet with aluminum structure.tank

RoboBarista: A Coffee Brewing Robot
Instructions from RoboBarista: A Coffee Brewing Robot
The first step to a good coffee brewing robot is to figure out how to brew good coffee. I've got some tips and tricks to brewing good coffee in the project logs ("A Dive Into the World of Coffee"), so I'll get directly into how I achieve good, full bodied...

IRK! Infrared Remote USB Keyboard
Instructions from IRK! Infrared Remote USB Keyboard
Through Hole Technology (THT) versionThis is how I built the Through Hole Technology version Make a double-sided fibre glass PCB (see front- and back- PDF files below). There are several ways to do this. The way I do it is to print the front and back...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
Solder LEDs and diodes to sparkfun board, be mindful of their orientation.Thread the leads of 16 LEDs (5mm or 3mm are fine, I used 5mm) through LED holes in the Sparkfun PCB. These boards are compatible with 4-lead RGB LEDs, so there are four available...

|<
<
1
2
3
4
5
>
>|