Close

212 Results for "%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%EC%82%AC%EC%9D%B4%ED%8A%B8%EF%BC%9Coptime4.com%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC %EC%9D%B8%EC%B2%9C%EB%A7%88%EC%82%AC%EC%A7%80 %EF%BC%9E %EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%E1%98%A3 %EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%EC%82%AC%EC%9D%B4%ED%8A%B8%E1%98%A3 %EC%9D%B8%EC%B2%9C%ED%9C%B4%EA%B2%8C%ED%85%94 %EC%9D%B8%EC%B2%9C%ED%82%A4%EC%8A%A4%EB%B0%A9 %ED%83%80%EC%9E%84"

  • Choose what modules you want in there
  • Instructions     from Fancy Power Strip
  • I modified two power strips. Once has the IR ToF sensor module (H08R60) to replace its power switch so that you can use hand gestures to turn on/off and the other one has a BLE and a USB modules so that you can control it via a smartphone or connect...

  • Looking at the Components
  • Instructions     from Automatic Arduino based IR Remote Control
  • 1) DHT11:- The DHT11 is a commonly used temperature and humidity sensor. The sensor comes with a dedicated NTC to measure temperature and an 8-bit microcontroller to output the values of temperature and humidity as serial data. The sensor is also factory...

  • Input Protection: Safety Matters !
  • Instructions     from Arduino Negative Voltmeter
  • This is the bi-directional diode clamping for over voltage or surge protection you may use in parallel to R_Low. I left this part in my build due to lack of space ! Bi-directional voltage clamp Safety should never be taken lightly ! These diodes will...

  • Parts Details
  • Instructions     from PROJECT MOOBA
  • Raspberry Pi B+: The Raspberry Pi 3 Model B+ is the final revision in the Raspberry Pi 3 range. Broadcom BCM2837B0, Cortex-A53 (ARMv8) 64-bit SoC @ 1.4GHz1GB LPDDR2 SDRAM2.4GHz and 5GHz IEEE 802.11.b/g/n/ac wireless LAN, Bluetooth 4.2, BLEGigabit Ethernet...

  • Wiring for UV Tube
  • Instructions     from Ultraviolet Microwave (name subject to change)
  • My instructions errs on making the wires too long. It’s easier to fix mistake with longer wires than too short. You can follow the schematic for how to wire this up and skip the detailed instructions. Take one of the tube wires and form it so that it...

  • Smart Device Controller
  • Instructions     from Smart Device Controller
  • Story Smart Device Controller This is a very interesting yet simple project for controlling ac appliances through phone calls. We called this project a "Smart Device Controller". By following this guide, you will be able to know and make your Smart...

  • Diy Simple Inverter
  • Instructions     from Diy Simple Inverter
  • Story Simple DIY Inverter An inverter that uses the minimum number of components for converting a 12 V DC to 220 V AC is called a simple inverter. A 12 V lead-acid battery is the most standard form of battery that is used for operating such inverters....

  • Lexitron RSS Reader
  • Instructions     from Lexitron RSS Reader
  • Tickernut circuit design and hardware:Enclosure:The motherboard is shaped to fit tightly inside a standard ABS jiffy box which set its limited size. The box has cutouts to expose all motherboard connectors on the left side and a small speaker and antenna...

  • J1772 Hydra
  • Instructions     from J1772 Hydra
  • Prepare the button by connecting three wires to a 3 pin .1" female SIP header. The center pin should be red, the outside pins green and black. The button will have 5 terminals on it, marked +, -, C (or COM), NO and NC. Connect the red wire to the + terminal,...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday