223 Results for "%E3%80%8A%EC%B5%9C%EC%A0%80%EA%B0%80 O1O%CE%9E5793%CE%9E7458%E3%80%8B %EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%8B%9C%EC%8A%A4%ED%85%9C%E3%86%8B %EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%85%94%EC%B8%A0%EB%A3%B8applause%EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%8B%9C%EC%8A%A4%ED%85%9C%EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%8B%9C%EC%8A%A4%ED%85%9C%EC%8B%A0%EC%82%AC%EC%95%84%EC%9D%B4%EB%A6%B0%EC%A3%BC%EB%8C%80caught %EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%E3%8F%87%E3%85%97%EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0queer"

Front end assembly
Instructions from OSUG: Open-Source Underwater Glider
Place a single 608ZZ bearing in each of “Syringe_clamp_front” and “Syringe_clamp_back” On the “Syringe_clamp_back” secure the bearing in place with the “Engine_bearing_fastener” piece, 3 M3 20mm...

rDUINOScope Boiana
Instructions from rDUINOScope Boiana
TEP 3 AssembleFor more detailed instructions, please visit the Project Website : http://rduinoscope.co.nf/rDUINO_step3.htmlNow is the time to create the Shield board. A Shield board is a board with pinouts which you stack on top of the ArduinoDUE board.Some...

Print parts
Instructions from Zvychai One
No step-by-step instructions here, follow your printing intuition/experience, but few tips would be: I'd say print everything except small covers with 3-4 walls and 30-40% infill. Most parts do not require much printing support except maybe if you have...

The Talking Microtronic Computer System Emulator
Instructions from The Talking Microtronic Computer System Emulator
Set up the hardware - the emulator main sketch shows the pin layout: // // SD+Ethernet Shield (optional) // #if defined (SDCARD) #define SDCARD_CHIP_SELECT 4 // // software serial interface for Emic 2 TTS module (optional) // #if defined (SPEECH) #define...

Main Wiring
Instructions from Capacitive Gamepad
Connect MPR121 to arudino i2c and power. On a Micro this is pins 2&3 plus VCC and GND. Flash the arduino and make sure everything works as you like. Breaking out the RST pin to a tactile switch is probably unnecessary, i've had no problem re-flashing...

Cuts required
Instructions from The Learner's Heliostat
The plywood product I used was 1/2x2x4 G1S, $37 ea before tax in Ontario in summer of 2022. For the project infrastructure, four 1" x 4" x 8' knotty pine planks would be price competitive and less work to waterproof, but less convenient to transport....

▇▇▇▇ D Flip Flops ▇▇▇▇
Instructions from FPGA Bootcamp #0
The SR latch modified with the inverter is often called a D latch because the single input is data for the latch to store. To make it a D flip flop, though, you need to arrange to capture the data at a clock edge, not just any time the latch is enabled....

Code for single Esp32 Board
Instructions from Bluetooth Tracker
This is the code for everything on a single Esp32 Board. Since I didn't have the correct board, I needed to use two of them, and they communicate through the serial port.The Bluetooth packets address and raw data get printed to the Arduino Serial...

HariFun#132 Sixteen Channel WiFi Remote
Instructions from HariFun#132 Sixteen Channel WiFi Remote
=== WebClient Sketch ===// PCF8574 WebClient, watches buttons and sends /inline?state=x to WebServer // Hari Wiguna, 2016 #include // Declare and set these two variables here or in an include file //const byte credentialCount = 2; //IMPORTANT! Change...

Assembly Code
Instructions from 8051 Alarm Clock
ROA EQU 7FH ;es Reloj o es Alarma USR EQU 50H ;Unidades de Segundos del Reloj DSR EQU 51H ;Decenas de Segundos del Reloj UMR EQU 52H ;Unidades de Minutos del Reloj DMR EQU 53H ;Decenas de Minutos del Reloj UHR EQU 54H ;Unidades de Horas del...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
I attached a 2 axis gyroscope and 3 axis accelerometer onto this project so that I could add some interesting control to the device. The 5 degrees of freedom board from Sparkfun outputs data from its gyroscope and accelerometer as analog voltages. I...

Circuit Connection:
Instructions from DIY Arduino Tic Toc Toe Game
Connect the push buttons keypad to Arduino Uno as shown in circuit diagram.(R1~A0,R2~A1,R3~A2,R4~A3,C1~A4,C2~A5,C3~Pin 2,C4~Pin 3).Also take a extra push button(Reset Button) and connect to Arduino.(Reset,GND).Connect all the pixel LEDs.(-Ve/GND~GND,+Ve/5V~5V,Data...

Prep Your Board!
Instructions from Sotto: A Silent One-Handed Modular Keyset
Cut your protoboard to roughly fit the size of the Feather. Use your wires to take the inconveniently placed pins and turn them into tidy little rows of four. The rows should be: A0 3v Gnd 11 A1 3v ...

Trinket LED Thermometer
Instructions from Trinket LED Thermometer
Here's a functional program to initialize the hardware, read temps, and display temps as colors. Enhancements such as multiple sensors/LEDs per Trinket are possible but left as an exercise for the reader./* trinket_thermo ---------------------------------------------------------------------------------...

Setting Up the Drone Transmitter
Instructions from DIY Radio Controller for Drone | nRF24L01
In this step, we will complete the Transmitter setup. We will do the circuit part first and after that, we will upload the code to the Arduino UNO to wrap up the setup. The materials required for this step are the NRF24L01 Transceiver module, Arduino...

|<
<
2
3
4
5
6
>
>|