319 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》선릉레깅스룸㉹ベgrace레깅스룸Ｓ선릉레깅스룸선릉레깅스е я레깅스룸비용superstition 강남레깅스룸′강남레깅스§８fetch"

Arduino or Wemos Code
Instructions from WiFi Signal Strength Scanner Monitor or Checker
In the arduino code set your WiFi credentials char wifissid[] = "ENTER YOUR WiFi SSID HERE"; char wifipass[] = "ENTER YOUR WiFi PASSWORD HERE"; Normally, the signal strength is displayed in dBm. But for a non techie person, the signal strength in terms...

Cree Dimming Level
Instructions from Cree Dimming Level
Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...

Smile Station
Instructions from Smile Station
Well in this step I will focus on the code and getting it to work with Facebook and Flickr ....---------------------------------------------------------------------------------------------------------#!/usr/bin/env python# this file is run using this...

Smile Station
Instructions from Smile Station
From the last step you should have seen how to and where every thing is going. So lets get started with the power... I used a PC power supply I had. ( 500 Watt ) I cut out the + 12 v and rigged the power supply to come on when power is applied. ...

Futurama's Jack dispenser
Instructions from Futurama's Jack dispenser
In order to add wireless access point capability to your media server, you need to install hostapd (hostapd_8192cu from AUR if your wifi dongle is based on a rtl8192cu chipset) and dhcp. If you have installed yaourt as stated in an upper Build Instruction,...

The Dune Pain Box
Instructions from The Dune Pain Box
Winding the inductors is easier than you might think! I used about 4 feet of 18GA Magnet wire to wind the inductors for this particular power supply. Each inductor has ~30 turns on it for an inductance of about 90uH. If you don't have...

Low Cost CO2 Laser Build
Instructions from Low Cost CO2 Laser Build
Assembling the tube1And now for assembling the laser tube itself. Things needed for this will be a bit of JB weld, a long thin dowl that fits inside your mirror mounts. This will help align them, much better than eyeing it. You will also need some 3/8th...

FireCoates
Instructions from FireCoates
Jacket Wiring, LED Setup, and Light Pipe Assembly.I never took pictures of this process with the first prototype so I need to complete the second prototype and take pictures to use as visual aides along the way, I should have them up in another week...

ATX power supply conversion for bench usage
Instructions from ATX power supply conversion for bench usage
Prepare the adapters and connect them to the terminal stripsThis part is important and tricky, and it took me three attempts to get this right. Here's the rules: Any high-current line must be a twin line that starts as a twin at the power supply's PCB...

Ice Station Thuban
Instructions from Ice Station Thuban
Plan out construction site. It helps to have snow on the ground, but is not mandatory. I used a 9.5 foot rope staked to the center of a circle to trace out the extents of my hemispherical dome. Note that my build was not on level ground, so I had to...

Portable travel NAS
Instructions from Portable travel NAS
Let's get cracking, get the Carambola up and running. I like to connect to the serial terminal, the development board features a usb ftdi chip allowing me to use a terminal program like PuTTy to connect.Connecting to serial terminalFirst step: see that...

Open IR Tracking Module
Instructions from Open IR Tracking Module
Interface Circuitry:[*Schematic]We'll need a small circuit to interface the IR camera to the arduino. I got all my information from other sources. Here is an exhaustive list:This fellow (kako) seems to be the first. Here are his pages translated. (Please...

Address Bus
Instructions from L-Star: Software-Defined 6502 Computer
This last step is going to get REALLY tedious because the Address Bus has so many lines. But this is the last step and you should be done, so keep it up just a little longer. A0: 6502 Pin 9 to FLiP pin 13 A1: 6502 Pin 10 to FLiP pin 14 A2: 6502...

USB Caliper HID
Instructions from USB Caliper HID
//--------------------------------------------------------------------- // USB Caliper HID // // version 0.1 - incomplete, only caliper read and output to USB // structure in place. Enough to read from Caliper // and output it. //---------------------------------------------------------------------...

Reviving tossed stepper motors
Instructions from Reviving tossed stepper motors
Now that we know what kind of stepper motor we have, we can build a simple test circuit to get the thing moving. At the bottom left, the control pins for the motor can be connected to any TTL logic device you wish to use to run the motor (in my project...

1
2
3
4
5
>
>|