166 Results for "soil+sensor"

Pinout
Instructions from WigwamBox - RaspberryPI GrowBox
Relay DevPIGND9IN131IN233IN335IN437VCC2 Display DevPIGND20VCC17SCL5SDA3 Soil Moisture Sensor DevPIAO-DO40GND14VCC4 DH-22 DevPI+1OUT29-6

Home automation using RF mesh network and arduino
Instructions from Home automation using RF mesh network and arduino
instructions for building the first sensor controller node.Parts required:Prototype board (3cm x 7cm)Arduino nanoRF transceiver (NRF24L01)Temperature/humidity sensor (DHT11) 1-2 relaysLight sensor (LDR)4.7uf capacitor 10k resistorWires and solder

TeensieWI woodwind USB MIDI controller
Instructions from TeensieWI woodwind USB MIDI controller
The MPX5010GP sensor is a bit bulky, so we use a dremel to cut off the mounting brackets on the sides, and we also make a diameter 14 mm (approx.) hole in the bottom sheet where the more narrow circular part of the sensor can fit. Offset the hole so...

Imaging
Instructions from Getting Cozy with the Diffraction Limit
Imaging A few issues presented themselves with respect to imaging. Monochromatic sensor First, a monochromatic sensor was not available for experiments. To keep the resolution high enough at the sensor, all pixels were color gain balanced to operate...

Make Flex sections
Instructions from Read Rope / Electronic Nerve
a. Cut a small piece of 5 hole x 2 hole perfboard that is big enough to contain a resistor, flex sensor, and 2 wires. b. Place resistor into perfboard.(10k for section 0, 24k for section 1, 56k for section 3) c. Place flex sensor into board. d. Connect...

Mechanical Design
Instructions from Sprout: Modern Indoor Self Watering Planter
The main body of Sprout is a 30cm X 15cm X 19cm Box made out of MDF. All Mechanical Design steps have been clearly demonstrated in the video attached at the start of the Instructable. You can also check it out at Sprout: Video/Mechanical DesignThe...

GETTING THE HARDWARE READY
Instructions from TableTennis Drone
The IR sensor that i have integrated consists of 5 connections namely VCC,GND,RESET,I2C pins SCL,SDAVcc is connected to BAT pin The breakout board provides I2c connections Pin 6 to SDA Pin 7 to SCL Pins 13 & 15 are the default pins for getting range...

Vinduino, a wine grower's water saving project
Instructions from Vinduino, a wine grower's water saving project
for casting needed:1 x 3/4" PVC pipe couplerpainters tape

Build humanoid leg
Instructions from RAPTA - Autonomous Humanoid Leg
The image here show the design of the full leg system, prepared in Lego Digital Designer. The list of components (BOM) are in the file Leg System.xlsx. The building instructions can be found in the Lego Digital Designer Leg...

Materials
Instructions from Network of Temperature Sensors
This is a perfect application for a $14 Raspberry Pi Zero WH as this device is compact, inexpensive, powerful, and has built-in WiFi. Here is the list of everything we need per sensor node and the approximate cost: Raspberry Pi Zero WH ($14)Micro SD...

Step 3: NodeMCU PCB Weather Station Shield
Instructions from IoT Personal NodeMCU ESP12 WiFi Weather Station
Design printed circuit board (PCB), I was used ,,Sprint-Layout" software. Exported to Gerber files. PCB was made https://jlcpcb.com To create this NodeMCU ESP12 weather station shield you will need: NodeMcu Lua CH340G/CH340/ ESP8266 Wireless WIFI Internet...

Step 4: Code
Instructions from EMT Conduit-Mounted Wind Sensors
Because the wind sensors refresh their output approximately every 0.8 seconds, the Arduino Nano must measure those analog signals either slower or at that same rate. After taking those readings, the Arduino outputs them to a PC/laptop over Serial protocol...

About HC-SR04 Ultrasonic Ranging Module
Instructions from Interfacing Ultrasonic Module HC-SR04 with Arduino
The ultrasonic sensor (or transducer) works on the same principles as a radar system. An ultrasonic sensor can convert electrical energy into acoustic waves and vice versa. The acoustic wave signal is an ultrasonic wave traveling at a frequency above...

CNC X axis
Instructions from WEEDINATOR 2019
The weeding mechanism is basically a rotating claw mounted on a CNC machine. The machine never tries to target individual weeds - this would be a big mistake - instead it will prevent weeds from ever reaching the surface by disturbing the soil during...

Prepare the Supplies
Instructions from Hand Gesture Smart Light Control
Use your pliers to bend the headers of the ultrasonic sensor, this way the sensor will be facing up when you solder it onto the perfboard. This is optional, but if you would like to reuse your Particle Photon, trim 2 female headers to match the male...

|<
<
1
2
3
4
5
>
>|