1565 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》강남레깅스룸ⓨ강남레깅스룸singing강남레깅스강남레깅스룸강남레깅스룸remainder 강남레깅스㉮┢선릉레깅스agitation"

Arduino or Wemos Code
Instructions from WiFi Signal Strength Scanner Monitor or Checker
In the arduino code set your WiFi credentials char wifissid[] = "ENTER YOUR WiFi SSID HERE"; char wifipass[] = "ENTER YOUR WiFi PASSWORD HERE"; Normally, the signal strength is displayed in dBm. But for a non techie person, the signal strength in terms...

Cree Dimming Level
Instructions from Cree Dimming Level
Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...

Create a function to decode the payload
Instructions from 2022 HDP 4 - Climate Resilient Communities
In order to decode the 23 bytes of payload that the sensor is sending we need to implement a decoder, in this case we need to create one custom. Once you select to create a custom decoder you just simply copy and paste the next code which is written...

Arduino-Compatible FPGA Shield
Instructions from Arduino-Compatible FPGA Shield
Step 2 - Import the Arduino board file into Altium Designer: Using Altium Designer (AD) requires that I import Eagle board into AD. AD14.x includes an Eagle importer. Used source files from the Arduino site to import in AD.

Setting up Linux AVR and ARM toolchains
Instructions from Setting up Linux AVR and ARM toolchains
INSTALLING MINT ON A RELUCTANT TOSHIBA SATELLITE LAPTOPDownloaded the latest Linux Mint 16 with Mate image via torrent from linuxmint.org. Burned to DVD and used it to boot the Toshiba. All seemed to be going well untill the boot finished and I tried...

Bench power supply
Instructions from Bench power supply
1) Come up with a simple good idea.2) Add good ideas to it.3) Try to implement it.4) When it fails, start to strip down the design to try to get it to work.5) Strip it down more6) More...7) Rejoyce when something simple works8) Add a few simple things...

Cumulus Wireless Sensor Platform
Instructions from Cumulus Wireless Sensor Platform
Solder the 2 x 22pF Supporting Capacitors for the Crystal Oscillator

Cumulus Wireless Sensor Platform
Instructions from Cumulus Wireless Sensor Platform
Solder the 3 x 220 Ohm Resistors (the 3 resistor spots nearest to the Crystal Oscillator)

Cumulus Wireless Sensor Platform
Instructions from Cumulus Wireless Sensor Platform
Solder 3 x 3mm LEDs (Top is Yellow, Bottom Left is Red, Bottom Right is Green)

Cumulus Wireless Sensor Platform
Instructions from Cumulus Wireless Sensor Platform
Connect the bottom-center + and - connection terminals to a 3V power source (CR3023 Battery, 2 x AA Battery, ..)

TI Launchpad Arcade Control to USB Interface
Instructions from TI Launchpad Arcade Control to USB Interface
Launchpad-Mame-Control TI Tiva C Launchpad firmware for Mame USB arcade controls adapterThis project is intended to design firmware for the TI Tiva C Launchpad development board to enable it to be used as a USB gamepad/mouse adapter for arcade and other...

Peril-Sensitive Sunglasses
Instructions from Peril-Sensitive Sunglasses
Accelerometer is wired like this:In my case I used:Analog 0 = X axisAnalog 1 = Y axisDigital 2 = 0g Detected

Back To The Future Time Circuit Clock
Instructions from Back To The Future Time Circuit Clock
Create (etch and solder) 5 PCB from big-module-shift and big-module-test - those are the display PCBs and drivers for 14-segment displays.

Back To The Future Time Circuit Clock
Instructions from Back To The Future Time Circuit Clock
Solder display PCBs to display driver PCBs using angular pin headers and in case of 14-segments, an additional ribbon cable connection is required.

Back To The Future Time Circuit Clock
Instructions from Back To The Future Time Circuit Clock
Connect driver boards with ribbon cables. 7-segment display boards and led board uses 10 wire cable, 14-segment displays use 12 wire cables.Note that there is no 12 wire IDC plug, so I used 14 wire plug and left the last two wires unconnected on the...

1
2
3
4
5
>
>|