242 Results for "%E3%80%8A%20%EC%98%88%EC%95%BD%EB%AC%B8%EC%9D%98%20OIO%E2%86%978489%E2%86%978306%E3%80%8B%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80%E2%94%A6%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80world%EC%84%A0%EB%A6%89%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80%EC%82%AC%EC%9D%B4%EC%A6%88%EC%B2%AD%EB%8B%B4%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80promotion%20%EC%84%A0%EB%A6%89%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80%E2%94%AB%20%E2%88%AB%EC%84%A0%EB%A6%89%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80decided"
Components: Blue Robotics 4-core Ping Cable (11 metres), 2 x 4.5mm WLP-M06 cable wet link penetrators including nuts, o-rings, and silicone seal, plus 2 x cut shake-proof washers, 1 x rubber strain relief boot , 2 x Micro JST 2-way female connectors....
I wanted to use a BMP280 I had in my parts bin for altitude measurements. I have used it in the past for a simple weather station and it works great! Turns out, it is even the go to sensor for Stratux, so I went ahead and plugged it in, activated it...
Flash a NodeMCU firmware imageFor flashing a new image, I use esptool. Plugin your NodeMCU module to an USB port, clone the esptool project and flash your firmware. Usually a new device will appear, like /dev/ttyUSB0. Step by step:git clone https://github.com/themadinventor/esptool.git...
CalibrationCalibrating the X/Y-axis of a plotter or CNC machine is actually quite easy. I did it as described in this video. First i had to know the theoretical steps/mm per axis. To calculate this value I multipliedthe steps/rev. (200 for most NEMA...
FINDING THE RESISTOR VALUESolder a 10K resistor to the Zero's header connector hole at pin 12, and connect the other end to the meter plus terminal. The meter minus terminal is connected to pin 14. To test it type the following: sudo gpio -g mode 18...
Move camera under model and select Bottom Polygons with Right Mouse Button Then select Move Tool and set Y to 50 Select exactly the Foundation copy Then open Scale Tool and set X and Z to 80
Building the DriverInstall prerequisite packages on Raspbian to build the kernel.#make sure everything is up to date sudo apt-get update && sudo apt-get -y upgrade #install tools sudo apt-get -y install bc rpi-update git libncurses5-dev Get the kernel...
Solder the components of the Onboard Gateway V1.0 PCB. The following image shows all the required components, with an identification number. Components list: TERM BLK 2P SIDE ENT 5.08MM PCBCONN HEADER R/A 2POS 2.5MMCONN HEADER VERT 2POS 2.54MMCONN...
=== WebClient Sketch ===// PCF8574 WebClient, watches buttons and sends /inline?state=x to WebServer // Hari Wiguna, 2016 #include // Declare and set these two variables here or in an include file //const byte credentialCount = 2; //IMPORTANT! Change...
Add your Milight lights to the ha-bridge software Open up the ha-bridge software in your browser (http://raspberry-pi-IP-address:80/), it runs on port 80 by default.You'll see a list of bridge devices, click add.Set a name and description to your likings....
Once you are able to compile the Blink code into the SIMATIC IOT2000 you can continue with the following steps: 1. Copy and paste the code below in your Arduino IDE. Once you have pasted the code be sure assign the unique Ubidots TOKEN where indicated....
In order to decode the 23 bytes of payload that the sensor is sending we need to implement a decoder, in this case we need to create one custom. Once you select to create a custom decoder you just simply copy and paste the next code which is written...
Begin with: 700 grams of filtered tap water from the frige in the break room. Poured into the same 5” stainless steel container that I used to cook inside yesterday. At 9:55 turn heat on and add: 6x70 = 420 grams of Sodium Hydroxide At 10:06 I...