2130 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 쓰리아워가격ｕ 쓰리아워가격earth강남쓰리아워강남쓰리아워쓰리아워enter 강남쓰리아워ぶЪ강남쓰리아워most"

Supplies
Instructions from DIY Smart 3D Printer Enclosure
1x Duct Fan 1x Dryer Vent Hose 1x Draft Blocker Backdraft 1x FireBeetle 2 ESP32-E 1x Gravity Environmental Sensor 1x Relay Module 1x IRF520 Mosfet 1x L7805CV Voltage Regulator 1x Super Bright LED Light 1x Mylar...

Free Presidential Style Hotline
Instructions from Free Presidential Style Hotline
MSP430G2231 Code:For a starting point I used this excellent project from Stefan Wendler. MSP430G2231 Software UART. The code below replaces main.c from his “timer-a-uart” branch.#include #include #include "uart.h" #define BUTTON BIT3 //...

HP Touchpad Charging Wall Mount
Instructions from HP Touchpad Charging Wall Mount
I took the end of an extension cord and wired it to power from the switchbox below to accept the plug-in charger for the Touchstone. I had a switchbox on the opposite side of this wall that could house the charger and keep it accessible for safety and...

Solid-state garduino with RTC & LCD!
Instructions from Solid-state garduino with RTC & LCD!
If you can't safely wire 120VAC, please stop here. I bear no responsibility for any bodily injury, death, or loss of property as a result of mimicking this project.Wired 120VAC through the Solid State Relays, outlets, and switches shown in the schematic.Within...

The control circuit
Instructions from Projector Screen
The relay coil is driven by 'remote power' output on the projector. There are no other connections made to the coil. As such, this also performs the needed isolation so if you screw up anything else, you at least don't fry your projector. The projector...

Smile Station
Instructions from Smile Station
From the last step you should have seen how to and where every thing is going. So lets get started with the power... I used a PC power supply I had. ( 500 Watt ) I cut out the + 12 v and rigged the power supply to come on when power is applied. ...

Sci-fi grade Home Automation
Instructions from Sci-fi grade Home Automation
For the outlet power detectors:Cut the connectors off of your two wall warts and solder the grounds together (and to the ground on their Arduino)Solder the +5v wire of one wall wart to the +5v plug on the Spark core, and the other to digital input 3...

Sci-fi grade Home Automation
Instructions from Sci-fi grade Home Automation
To build the light switches (I'm not using these, but they might work better for those of you who don't rent):Using the pictues below as guides, solder the relevant wires to the Arduino...I kid.There are a few important parts here: There's the Arduino,...

Sci-fi grade Home Automation
Instructions from Sci-fi grade Home Automation
Building the blind minder breakout board:For this one, I think I'm just going to give a picture, a sketch, and the STL files. It's so simple it's not even really worth a full build log.Clockwise from the top left, the outbound pairs are:9V brick (for...

RF light switch
Instructions from RF light switch
Transmitter: 4.5-5V supply must be thrown towards the ATtiny. The RF transmitter works best with 12V, but 4.5V proved to be enough for 35m distance (even with the receiver inside the house).The LED is just for an indication that the button press...

RF light switch
Instructions from RF light switch
Mains voltage alert:Now it's time to connect your mains voltage. In my case I wired the relay in series with the normal switch, so the switch needs to stay on. In retrospect, parallel would have worked much better, but in my case it would have made the...

Awesome Jacket
Instructions from Awesome Jacket
As shown in the photo, the prototyping card also supported a DIN connector that included the audio output to a speaker, 5V, and a switch cct (gnd+sense) that led to a speaker and ultimately a "kill switch".

Awesome Jacket
Instructions from Awesome Jacket
The speaker was re-purposed from an old Motorola hands-free set. It is a unit with a housing that included a decent speaker, power ccts, and amplification. A coiled cord ran out one end to an auto lighter adapter and a second coiled cord ran to a jack...

Awesome Jacket
Instructions from Awesome Jacket
The kill switch was constructed using a short piece of 1.5" ABS plumbing tube and two end caps. Through one end cap I ran a multi-wire cord that carried 5V and the switch cct; to the other end I connected a stereo plug to match the jack described above....

GLaDOs Replica for RORI
Instructions from GLaDOs Replica for RORI
Assemble itFor the head :Put the RGB LED.Then, fix the camera:And the two servomotors:Then, the high part of the body:The fix the down part and the base (One motor is missing because I don't receive it):Put the sticker:Get some wires:Build the first...

1
2
3
4
5
>
>|