996 Results for "%E3%80%8A%20%EC%98%88%EC%95%BD%EB%AC%B8%EC%9D%98%20OIO%E2%89%A1%E2%91%A7%E2%91%A389%E2%89%A183O%E2%91%A5%E3%80%8B%EC%84%A0%EB%A6%89%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%E3%89%B9%E3%83%99grace%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%EF%BC%B3%EC%84%A0%EB%A6%89%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%EC%84%A0%EB%A6%89%EB%A0%88%EA%B9%85%EC%8A%A4%D0%B5%20%D1%8F%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%EB%B9%84%EC%9A%A9superstition%20%EA%B0%95%EB%82%A8%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%E2%80%B2%EA%B0%95%EB%82%A8%EB%A0%88%EA%B9%85%EC%8A%A4%C2%A7%EF%BC%98fetch"

Arduino or Wemos Code
Instructions from WiFi Signal Strength Scanner Monitor or Checker
In the arduino code set your WiFi credentials char wifissid[] = "ENTER YOUR WiFi SSID HERE"; char wifipass[] = "ENTER YOUR WiFi PASSWORD HERE"; Normally, the signal strength is displayed in dBm. But for a non techie person, the signal strength in terms...

1 - Take an A4 paper
Instructions from Covid 19 washable origami mask

AM2XBee4RC
Instructions from AM2XBee4RC
Mount your hardware and solder the appropriate wires from your ADC pads, GPIO pads and other components together. Each build will most certainly be unique so use your discretion as to which component attaches to which Arduino pin. I used the following...

[2016] InternetS of Energy - Call me DAISEE
Instructions from [2016] InternetS of Energy - Call me DAISEE
Ethereum installation on a Raspberry PIAn Ethereum node running on a Raspberry Pi. Photo by RIeul (CC-BY-NC-SA) Equipment 3 Raspberry Pi with Ethereum client (each Pi = a node of a blockchain) 3 SD cards 2 computers Other solution Using Wio Link to simulate...

Pedal Wiring
Instructions from Pedalino™
Pedalino is designed to work with the majority of expression pedals on the market, but there are a few popular pedal types which are incompatible and need to use adapters in order to work with Pedalino. There is no recognized standard for footswitch...

Cree Dimming Level
Instructions from Cree Dimming Level
Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...

Make 20 vactrols
Instructions from PHOSPHOR Video Distortion
In order to control the video effects via MIDI, I needed a part that could override the potentiometers. For full effects, I need less than 30 ohms, to switch an effect off completely, a resistance of more than a few kohms would be desirable. I couldn't...

Step 20: Gather components for sub-sea cable
Instructions from "Mercator Origins": Sat Nav & Telemetry for Divers
Components: Blue Robotics 4-core Ping Cable (11 metres), 2 x 4.5mm WLP-M06 cable wet link penetrators including nuts, o-rings, and silicone seal, plus 2 x cut shake-proof washers, 1 x rubber strain relief boot , 2 x Micro JST 2-way female connectors....

Connections
Instructions from TRICORDUINO - 3.0 True Scientific Tricorder
You can find every information about Feather MO Adalogger in: https://learn.adafruit.com/adafruit-feather-m0-adalogger/overview I have used all pins of Feather and I would like to have more pins available. These are the connections of the set: Pin00-...

Prep Your Board!
Instructions from Sotto: A Silent One-Handed Modular Keyset
Cut your protoboard to roughly fit the size of the Feather. Use your wires to take the inconveniently placed pins and turn them into tidy little rows of four. The rows should be: A0 3v Gnd 11 A1 3v ...

Cabling the MPE device's hardware-components
Instructions from MPE-DIY-Device
Power supply: Ground - GND from Teensy (power-rail as described in the PDF attached) +3.3V - 3.3V from Teensy (power-rail as described in the PDF attached) Joystick 1: VRx - Pin 23/A9 (horizontal control) VRy - Pin 22/A8 (vertical control) SW - Pin 01...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
I attached a 2 axis gyroscope and 3 axis accelerometer onto this project so that I could add some interesting control to the device. The 5 degrees of freedom board from Sparkfun outputs data from its gyroscope and accelerometer as analog voltages. I...

Working of an AC
Instructions from Air Conditioner PCB Tutorial With its Working
An air conditioner collects hot air from a given space, processes it within itself with the help of a refrigerant, and a bunch of coils and then releases cool air into the same space from where the hot air had originally been collected. This is essentially...

Prepare the ESP3266 (Wemos D1 Mini)
Instructions from GeoLeaf
The ESP8266 is next, connect it to your computer using a USB cable and then navigate to https://install.wled.me/ using the chrome web browser. Press ‘Install’ and then choose your board. Once completed we can then disconnect this and set it...

Wiring Up the Circuit (Wemos D1)
Instructions from Wi-Fi Controlled Robot Using Blynk App
In the video above I show you how you can assemble the electronics in the robot structure. A power pack made of three 18650 batteries was installed on the back of the robot. It provides 11.1V (3 x 3.7V) to the robot. That's enough to power the 12V DC...

1
2
3
4
5
>
>|