Close

526 Results for "%EC%84%A0%EB%A6%89%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%E3%80%8Eoio_%EF%BC%94%EF%BC%96%EF%BC%94%EF%BC%98_%EF%BC%90%EF%BC%99%EF%BC%93%EF%BC%90%E3%80%8F%3E %EA%B0%95%EB%82%A8%EC%85%94%EC%B8%A0%EB%A3%B8 %E2%88%88%EC%84%A0%EB%A6%89%EC%9C%A0%ED%9D%A5 %E2%88%83%EC%84%A0%EB%A6%89%EB%9E%80%EC%A0%9C%EB%A6%AC %E2%88%8F%EA%B0%95%EB%82%A8%EB%A3%B8%C2%B1 %EA%B0%95%EB%82%A8%EC%9C%A0%ED%9D%A5 %E2%88%91%EA%B0%95%EB%82%A8%EB%A3%B8%EC%8B%B8%EB%A1%B1 %EA%B0%95%EB%82%A8%EB%9E%80%EC%A0%9C%EB%A6%AC %E2%88%80%EC%84%A0%EB%A6%89%EC%85%94%EC%B8%A0%EB%A3%B8%2B %EC%84%A0%EB%A6%89%EB%A3%B8%EC%8B%B8%EB%A1%B1%E2%88%86 employee"

  • Cree Dimming Level
  • Instructions     from Cree Dimming Level
  • Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...

  • Pedal Wiring
  • Instructions     from Pedalino™
  • Pedalino is designed to work with the majority of expression pedals on the market, but there are a few popular pedal types which are incompatible and need to use adapters in order to work with Pedalino. There is no recognized standard for footswitch...

  • AM2XBee4RC
  • Instructions     from AM2XBee4RC
  • Mount your hardware and solder the appropriate wires from your ADC pads, GPIO pads and other components together. Each build will most certainly be unique so use your discretion as to which component attaches to which Arduino pin. I used the following...

  • Provisioning the Raspberry Pi
  • Instructions     from GePS
  • Next, you're going to get the SD card ready for booting the operating system on the Raspberry Pi. This begins with copying the official raspbian lite image to the SD card. This is a process that can be done in many ways, and it slightly differs depending...

  • Wire
  • Instructions     from Hybrid Sim Yoke
  • Wire as follows:  Both potentiometers Pin 1: 5v Both potentiometers Pin 3: ground Left potentiometer Pin 2: A0 Right potentiometer Pin 2: A3. Note that they have two channels, and all three wires have to connect to the same channel...

  • Step 1: 3D printing
  • Instructions     from UltraTower
  • To build a tower you will need to print the 3D parts shown on the left of the image. The "Sensors float" part is optional, print it if you want to use the pH and EC sensors. You will need 12 times the part: "Basket".  You can download the files...

  • Step 1: 3D printing
  • Instructions     from UltraTower 2023
  • To build a tower you will need to print the 3D parts shown on the left of the image. The "Sensors float" part is optional, print it if you want to use the pH and EC sensors. You will need 12 times the part: "Basket".  You can download the files...

  • Connect to Arduino
  • Instructions     from 4-Channel Optogenetics Pulser
  • Plug the collated ground wires into an Arduino Ground pin, and the collated +5V wires into a +5V pin (if using a Due, use the +3.3V pin or you will damage the microcontroller) and plug the other jumper wires into the correct I/O pins: Toggle switches...

  • I2C Sensors and debugging
  • Instructions     from Stratux ADSB Receiver and AHRS
  • I wanted to use a BMP280 I had in my parts bin for altitude measurements. I have used it in the past for a simple weather station and it works great! Turns out, it is even the go to sensor for Stratux, so I went ahead and plugged it in, activated it...

  • Cabling the MPE device's hardware-components
  • Instructions     from MPE-DIY-Device
  • Power supply: Ground - GND from Teensy (power-rail as described in the PDF attached) +3.3V - 3.3V from Teensy (power-rail as described in the PDF attached) Joystick 1: VRx - Pin 23/A9 (horizontal control) VRy - Pin 22/A8 (vertical control) SW - Pin 01...

  • Prep Your Board!
  • Instructions     from Sotto: A Silent One-Handed Modular Keyset
  • Cut your protoboard to roughly fit the size of the Feather. Use your wires to take the inconveniently placed pins and turn them into tidy little rows of four. The rows should be: A0   3v   Gnd   11 A1    3v ...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday