Results for ↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 쓰리아워가격К 쓰리아워레깅스룸realmが쓰리아워쓰리아워레깅스룸강남술집정보better 쓰리아워㎶강남쓰리아워ゲⓝ강남쓰리아워recognition

Pressure Cooker Vacuum Chamber
Instructions from Pressure Cooker Vacuum Chamber
Step 6: Vacuum time Well, we're finally here. It's time to turn on the vacuum pump, and run for cover. Maybe.Before we actually flip the switch, a few words of caution from our sponsor.First, be sure to read the instructions that came with your pump....

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
Two 74HC595s (wired in parallel) will be driving all the LEDs in the project as well as providing power to all of the buttons. The 74HC595 is an 8 bit serial in parallel out shift register. I've written a detailed tutorial about multiplexing with the...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
The 74HC595 can only do parallel output, so I used a 74HC165 to measure the state of the buttons via 4 current limiting resistors and send this information to the Arduino. More info about the chip can be found on its datasheet.The 74HC165 has the following...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
This instrument is primarily a MIDI device, so we need to build a MIDI out. There are two ways to do this (and over the course of this project I did one and then switched to the other):output MIDI via a 5 pin DIN connector output MIDI via USB (this is...

FireCoates
Instructions from FireCoates
Optional 3D Printed Jacket Module CaseDownload the Base and Top to the case and print them on your favorite RepRap OpenSource 3D Printer. It should come out looking similar to this(colors may vary ;) ):The headphone jack hole may need to be cleaned up...

ATX power supply conversion for bench usage
Instructions from ATX power supply conversion for bench usage
Add terminal strips and mounting helpers to the base plate:I later replaced the terminal strips shown in the picture (6 mm²) with bigger ones (10 mm²) because they were simply easier to work with.The PVC tubes are used to hold cable ties. Use...

TS9 to F connector
Instructions from TS9 to F connector
Cut off a short section of RG-59 cable. Strip both ends so you are left with the center conductor, an inch of exposed wire on one end, and 3/8in on the other. Rotate it between your fingers and sand down the remaining foam insulation so it...

4G LTE Yagi antenna for ATT
Instructions from 4G LTE Yagi antenna for ATT
Get some rivets long enough to go fully through your director. The normal 'long' 1/8th in AL rivets at my local hardware store were perfect (with the countersink created in step 10).

Goliath - A Gas Powered Quadcopter
Instructions from Goliath - A Gas Powered Quadcopter
Building the ExhaustTools: Chop Saw or Reciprocating Saw, Files, Welder, Torx (T40) bit, Socket Wrench, 1/4" and 7/16" socketsA) Cut the materialsUsing the chop saw or reciprocating saw, cut the 1" diameter U-Turn and the 135 Bend, as well as the 1 1/8"...

ramanPi - Raman Spectrometer
Instructions from ramanPi - Raman Spectrometer
Below is a list of build instruction logs that will instruct you on how to go all the way from sourcing your components to printing the parts, and constructing your very own raman spectrometer!To begin, you will need some tools.. Pretty much every...

ramanPi - Raman Spectrometer
Instructions from ramanPi - Raman Spectrometer
Section: 6A complete Filter Selector AssemblyComponents Required: Printed versions of the following 3D Printed Objects from the gitHub repository: mechanical_device_filterSelectorAssembly_frontmechanical_device_filterSelectorAssembly_backmechanical_device_filterSelectorAssembly_filterWheelmechanical_device_filterSelectorAssembly_centerHub_Backmechanical_device_filterSelectorAssembly_522nmSP_covermechanical_device_filterSelectorAssembly_550nmSP_cover(1x)...

ramanPi - Raman Spectrometer
Instructions from ramanPi - Raman Spectrometer
Section: 7A Completed Spectrometer. A note might be made here that this spectrometer can and will function as an independant device connected to a regular PC running the ramanPi spectraCide software! If you wanted to use it and not build...

ramanPi - Raman Spectrometer
Instructions from ramanPi - Raman Spectrometer
Section: 10A completed optical Assembly including the Raman Section and the Spectrometer.Components Required: A completed objectiveLens MountA completed beamSplitter AssemblyA completed laserShutter AssemblyA completed mirrorMount...

Turn a cigarette lighter into an IR Nikon remote
Instructions from Turn a cigarette lighter into an IR Nikon remote
5.Program your microcontroller with the following BASCOM code:''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''' Infrared Remote Control Transmitter for Nikon D90' -------------------------------------------------'' ...

ATX Benchtop Power Supply
Instructions from ATX Benchtop Power Supply
Calculations in hand, head to your local surplus store. In the midst of getting lost in a sea of ammo cases, CB radios, unidentifiable motors, and assorted pieces of self-adhesive foam, collect some parts:You'll note that they didn't have any large wattage...

1879 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 쓰리아워가격К 쓰리아워레깅스룸realmが쓰리아워쓰리아워레깅스룸강남술집정보better 쓰리아워㎶강남쓰리아워ゲⓝ강남쓰리아워recognition"