Close

4290 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》레깅스룸견적よ레깅스룸ago레깅스룸メ강남레깅스룸eighty 선릉레깅스룸κ선릉레깅스⒲레깅스룸メｃ선릉레깅스룸literary"

  • HPDL watch
  • Instructions     from HPDL watch
  • Let's start with PCB. I wanted to mound display on one side of the PCB and the uc - on the other. Unfortunatelly, uc barely fits in the middle of the display's back and some pinout traces of display and uc touches where they mustn't. The traces...

  • HPDL watch
  • Instructions     from HPDL watch
  • The code is next. It's available at my github, I'll just explain a little bit. The timer2 is set to overflow and it's prescaled to 1024. With 32768 Hz clock it overflows every 8 seconds. Then I add 8 secs to the time variable. I've also set INT0...

  • HPDL watch
  • Instructions     from HPDL watch
  • Make a whristlet:It is very easy. You can see holes on my manufactured PCB. I just mounted screws through them and bent 2 pieces of wire like in the foto which can be placed on those screws over cut off gaps of PCB. The whristband itself is made...

  • Seeing the invisible
  • Instructions     from Seeing the invisible
  • 2) Acquire the lenses. There are quite specific requirements for the lenses. First find the focal length of the lens. This could be done a number of different ways. You could go outside and focus the light from the sun to a point (It will burn things),...

  • Guided Rocket
  • Instructions     from Guided Rocket
  • Drill 3mm holes in the necessary spotsScrews ready for mountingOuter ring will be attached to this pivot

  • FireCoates
  • Instructions     from FireCoates
  • Optional 3D Printed Jacket Module CaseDownload the Base and Top to the case and print them on your favorite RepRap OpenSource 3D Printer. It should come out looking similar to this(colors may vary ;) ):The headphone jack hole may need to be cleaned up...

  • Craig-o-Matic
  • Instructions     from Craig-o-Matic
  • I found the Adafruit small mint tin perf board to be ideal to mount two DC barrel connectors and the Arduino pro mini. I mounted it to the ammo box using some 1/2 " standoffs.

  • TS9 to F connector
  • Instructions     from TS9 to F connector
  • Cut off a short section of RG-59 cable.  Strip both ends so you are left with the center conductor, an inch of exposed wire on one end, and 3/8in on the other.  Rotate it between your fingers and sand down the remaining foam insulation so it...

  • Goliath - A Gas Powered Quadcopter
  • Instructions     from Goliath - A Gas Powered Quadcopter
  • BUILDING THE UPPER FRAMETools - Miter Saw, Jig Saw or Tin Snips, File, Drill with #30 drill bit,Rivet PullerA) Build the Jig for the Upper FrameTo properly build the frame, jigs are required to hold all of the frame elements in place. The jig is constructed...

  • Single Chip AVR BASIC Computer
  • Instructions     from Single Chip AVR BASIC Computer
  • Required Components:The component list for this computer is fairly low as only a single IC is required: 1 x ATmega 1284P Microcontroller 1 x DIL 40 Pin 0.6" IC Holder 1 x 40 Pin Female Pin Header (to be cut down into smaller headers) 1 x 16 MHz Crystal...

  • Single Chip AVR BASIC Computer
  • Instructions     from Single Chip AVR BASIC Computer
  • The Circuit:I designed the circuit diagram in the program Fritzing as it had all the required footprints readily available. The circuit is fairly simple as the ATmega 1284P has the minimum hardware connections required (along with a 16MHz crystal) to...

  • Single Chip AVR BASIC Computer
  • Instructions     from Single Chip AVR BASIC Computer
  • The PCB:Once I had used the program Fritzing to design the PCB, it was sent off to a PCB manufacture to be produced using the isolation milling process. The PCB is single sided as a double sided PCB was not needed, due to the fairly low component count...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday