928 Results for "8-bit cpu"

The basics - know your options
Instructions from A guide to custom Joysticks
In this instruction I will talk about hardware options and potential usage ideas of the components. I will not go in the exact details and scientific explanations - there is not need for it because there are tons of excellent articles about all of them...

Hello World!!! - the first Joystick program
Instructions from A guide to custom Joysticks
For this instruction I used following components: 1 x Arduino Pro Micro1 x Analog Joystick breakout board1 x Small push button Using the flying wire method described in instruction 3 the test joystick looks like this Preparation of the Arduino IDE In...

Solder 1206 capacitor and resistor practice stalks
Instructions from SMT Garden
Gather your supplies. You'll need: a soldering iron (60W min) set to 700-750F (370-400C)a fine but not sharply pointy tip (0.8mm is good and we prefer bent tips)a flux pen (rosin RMA or water-soluble, most no-clean is not active enough)small diameter...

The top 3D-printed Raspberry Pi cases
Instructions from The top 3D Printed Raspberry Pi cases
If you are looking for the best 3D-printed Raspberry Pi cases, then you have come to the right place. In this article, we will be discussing the top 10 3D-printed Raspberry Pi cases that are available in the market. We all know that the Raspberry...

How to generate an animation with the Block Move command (BoingBall)
Instructions from NTSC/PAL Video Display Shield
I used a 8-frame GIF animation of the famous Amiga BoingBall and separately saved the frames with the help of IrfanView. With the same program the images got scaled that the ball had a size of 30 x 30 pixels with a 1 pixel border on all 4 sides making...

Step 5: Uploading Arduino Codes & Conclusion
Instructions from Spider Robot with Arduino
We have prepared a code for you so that you can move the spider robot without any problems at first. A few commands are ready in the code, but you can revise it yourself ;#include // include IR Remote library #include // include servo library //=====...

The NanoStillery™ - Whiskey Distillery
Instructions from The NanoStillery™ - Whiskey Distillery
Adafruit GPRS Feather Code The crux of this code is the 'unravelData()' function which receives the stream of data and turns it into a character arrays called 'rabbits'. These arrays are then pretty much ready to be passed over to the FONA module for...

Implement Charts/Graph
Instructions from Expense Tracker App
Type the following command to install the chart.js plugin: npm install chart.js --save Import the chart to the page where we need to use by typing the following code: import { Chart } from 'chart.js'; For this project, we are using the chart...

Code
Instructions from ESP32 Personal Bat Signals with Light and Sound
I used micropython, because I haven't used it for a project yet and I was shocked how well it worked for this. There are many tutorials on how to use Thonny with an ESP32, and I found it to be much quicker than doing this in Arduino/ C++. The main files...

Instructions:
Instructions from Laser XY Scanner
Step 1: Gather Your Components Laser XY Scanner - BOM I usually like to source my parts from DigiKey, but the low-cost options on Amazon are hard to beat sometimes. This list is just one of many sources for each component in the BOM. There are of...

CODE
Instructions from Open-Source Shallow Water Glider
The first code chunk declares the variables and establishes connections #include #include "Wire.h"#include #include "GravityTDS.h"#include #include #include "MS5837.h"#include "ping1d.h"#include "SoftwareSerial.h"#include "RTClib.h"#include //#include...

IRK! Infrared Remote USB Keyboard
Instructions from IRK! Infrared Remote USB Keyboard
Through Hole Technology (THT) versionThis is how I built the Through Hole Technology version Make a double-sided fibre glass PCB (see front- and back- PDF files below). There are several ways to do this. The way I do it is to print the front and back...

Front end assembly
Instructions from OSUG: Open-Source Underwater Glider
Place a single 608ZZ bearing in each of “Syringe_clamp_front” and “Syringe_clamp_back” On the “Syringe_clamp_back” secure the bearing in place with the “Engine_bearing_fastener” piece, 3 M3 20mm...

|<
<
60
61
62