Close

5651 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 강남쓰리아워ｈ 쓰리아워worship쓰리아워레깅스룸쓰리아워가격강남쓰리아워egypt 강남술집정보クＱ강남쓰리아워disorder"

  • The Dune Pain Box
  • Instructions     from The Dune Pain Box
  • First, here is the block diagram:You'll note that there are two relays in this circuit.  These are used to connect the HV output to the hand electrode, and turn on the 12V supply to the Amp and HV power supply.  You can spider wire them in...

  • The Dune Pain Box
  • Instructions     from The Dune Pain Box
  • To get a good idea how we made the electrodes, you can read the project update entitled "The Hand Thingie".  If you want to use the same sensing set up we used, this worked well.  Any sort of Object that is fairly ergonomic and can have the...

  • Animatronic AVP Predator cannon

  • Instructions     from Animatronic AVP Predator cannon
  • Cannon code- #include "Servo.h" // include the servo library Servo armServo; // servo to raise the arm Servo cannonServo; // servo to recoil cannon // these constants won't change: const int triggerSensor = 1; // the sensor is connected to analog pin...

  • Make and Feel Virtual Drawings
  • Instructions     from Make and Feel Virtual Drawings
  • Make Processing control Arduino THE FINAL PROGRAM:So,you have started drawing on Processing. Now, you'll 'feel' the drawing!Imagine you are blind (remember, this device was invented for blind people to draw on computers):How would you feel a raised line...

  • Make and Feel Virtual Drawings
  • Instructions     from Make and Feel Virtual Drawings
  • Hack a mouse (optional) Open the casing of the mouse, and remove the scroll roller.Now, you should have space to place the servo motor like in the picture.To paste servo motor on the mouse board, use a glue gun or double sided tape.Now, there should...

  • Ikea Lack Infinity Table
  • Instructions     from Ikea Lack Infinity Table
  • Acquire the table.These things are mostly made of cardboard. Not joking.For that reason, when you start cutting apart large internal sections of it, it start to become VERY weak. Try to leave a large edge section to help with the structure of the table,...

  • Ikea Lack Infinity Table
  • Instructions     from Ikea Lack Infinity Table
  • Painting. I used the cheapest home depot flat black paint I could find, I painted the whole top, inside, covered all my dremel marks. ;)I also laid out the led strip and put a sticky dot over each emitter, I then used some Duplicolor engine enamel and...

  • Ikea Lack Infinity Table
  • Instructions     from Ikea Lack Infinity Table
  • Once the paint is dry you can finish the assembly. I cut a small hole in the bottom of the table to run in some power, the controller and IR receiver sits in one corner of the table.  I put the planks with the led strings inside, connected the controller,...

  • Quick and Nasty Tube Power Supply
  • Instructions     from Quick and Nasty Tube Power Supply
  • Take the two 240V bobbins and put them together with the protective cardboard and anything else that looks important. Now it's time to reassemble all that iron!(In this example, I wound a filament winding on top of the second 240V winding. I don't actually...

  • Jewel Box Servo Meter
  • Instructions     from Jewel Box Servo Meter
  • Test fit all the components in the box to find the best arrangement. Cut a piece of strip board 8 rows wide and up to about 25mm long that will fit flat on the floor of the box. The strip board will act as a bus to connect to the header. I placed the...

  • Jewel Box Servo Meter
  • Instructions     from Jewel Box Servo Meter
  • Fasten the servo to the inside of the box with double sided tape. Measure the distance from the center of the drive gear to the box. Place little blocks in each corner of the box at the same level of the top of the servo hub. These will serve to hold...

  • Portable LED Floodlight
  • Instructions     from Portable LED Floodlight
  • So. This pole. It's a $50 thinwall fiberglass tube from China that's marked as a "windsock pole".That's more than 22ft. And even with no weight up at the top it's quite flimsy. I decided to pull out the top two sections which will shorten it by about...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday