405 Results for "%E3%80%8A%EC%B5%9C%EC%A0%80%EA%B0%80 O1O%CE%9E5793%CE%9E7458%E3%80%8B %ED%8D%BC%EB%B8%94%EB%A6%AD%EC%85%94%EC%B8%A0%EB%A3%B8%EC%B0%A8%EC%9D%B4%C5%8B %E3%80%8A%EC%B5%9C%EC%A0%80%EA%B0%80 O1O%CE%9E5793%CE%9E7458%E3%80%8B %E2%87%92silver%E3%8F%82%ED%8D%BC%EB%B8%94%EB%A6%AD%EC%88%A0%EC%A7%91%EC%84%A0%EB%A6%89%ED%8D%BC%EB%B8%94%EB%A6%AD%E3%85%9Eproprietary %ED%8D%BC%EB%B8%94%EB%A6%AD%EC%88%A0%EC%A7%91%ED%8D%BC%EB%B8%94%EB%A6%AD%EC%85%94%EC%B8%A0%EB%A3%B8%EC%B0%A8%EC%9D%B4 %EC%84%A0%EB%A6%89%ED%8D%BC%EB%B8%94%EB%A6%AD%C2%B9%ED%8D%BC%EB%B8%94%EB%A6%AD%EC%97%85%EC%86%8C%EC%8B%9C%EC%8A%A4%ED%85%9C%EF%BD%97sworn%E3%86%89"

▇▇▇▇ D Flip Flops ▇▇▇▇
Instructions from FPGA Bootcamp #0
The SR latch modified with the inverter is often called a D latch because the single input is data for the latch to store. To make it a D flip flop, though, you need to arrange to capture the data at a clock edge, not just any time the latch is enabled....

Program the Microcontroller
Instructions from Fear the Scary Cat!
Before mounting the prototype PCB to the housing, I recommend uploading the required sketch to the ATtiny84 microcontroller with a programmer of your choice. I used a USBtinyISP type shown in the picture. /*Sketch for the Scary Cat Project by Gene H*/...

Upload the Program to the Arduino Board
Instructions from Model Railway Layout With Automated Siding
Download the Arduino IDE from here if you don't have it on your computer. Then download and open the given code:int i=0; //Integer to store the locomotive's speed at a scale from 0 to 255. int switchLimit = 80;// Integer to store the speed limit...

Hardware setup
Instructions from Adafruit Ethernet FeatherWing to Ubidots
1. Plug in the Ethernet FeatherWing into the Feather board. 2. Connect one end of the Ethernet cable to the Ethernet FeatherWing and the other to your hub, router, or switch. Step 3. Programming With the following example code, we will publish...

Turn on and Troubleshooting Notes
Instructions from Flea-Scope USB O-scope (18 Msps, $13 BoM, WebUSB)
I first visually look for shorts/opens, especially on the QFN or QFP and USB (shorts can be easily reworked with the Kester 2331-ZX flux pen; always clean and dry boards after rework; I use isopropyl alcohol and a toothbrush followed by running water)....

Instructions
Instructions from DIY Ntrip Server and Reference Station Setup
DIY Onocoy Reference Station Setup GuideIn this guide, we’ll walk you through the process of setting up your own GPS Onocoy server using cost-effective hardware options and reliable GPS receivers. Whether you’re interested in enhancing the accuracy of...

rDUINOScope Boiana
Instructions from rDUINOScope Boiana
TEP 3 AssembleFor more detailed instructions, please visit the Project Website : http://rduinoscope.co.nf/rDUINO_step3.htmlNow is the time to create the Shield board. A Shield board is a board with pinouts which you stack on top of the ArduinoDUE board.Some...

3D printing the enclosure
Instructions from OpenRPNCalc
Here are a few more-or-less random notes about 3D printing the calculator enclosure. I've printed it with the Creality Ender 3 V2 printer using PETG plastic, and the case went really well I think. Contrary to what's written in many websites,...

Setting Up the Drone Transmitter
Instructions from DIY Radio Controller for Drone | nRF24L01
In this step, we will complete the Transmitter setup. We will do the circuit part first and after that, we will upload the code to the Arduino UNO to wrap up the setup. The materials required for this step are the NRF24L01 Transceiver module, Arduino...

wiring
Instructions from Gas Leakage Detection
-MQ135A0 = A0GND = GNDVCC = 5V-LED+ = D2- = GND

Instructions
Instructions from Budget DIY ESP32 GPS Base Station and Receiver
Best Budget DIY GPS/GNSS Base Station using the UM980 and a ESP32Introduction The ESP32 is a versatile microcontroller renowned for its WiFi and Bluetooth capabilities. In this guide, we’ll walk you through setting up the your ESP32 development board...

sdramThingZero - 133MS/s 32-bit Logic Analyzer
Instructions from sdramThingZero - 133MS/s 32-bit Logic Analyzer
Solder up them Address-Lines (And Clock)The core-concept behind sdramThing is that of loading (half of) the memory-locations with commands that will be (eventually) directly fed-back to the SDRAM itself. Taking into account the characteristics of SDRAM,...

AM2XBee4RC
Instructions from AM2XBee4RC
Mount your hardware and solder the appropriate wires from your ADC pads, GPIO pads and other components together. Each build will most certainly be unique so use your discretion as to which component attaches to which Arduino pin. I used the following...

▇▇▇▇ Understanding Basic Logic Gates ▇▇▇▇
Instructions from FPGA Bootcamp #0
Open the simulator using this link and you'll see the three fundamental logic gates that will build up just about all kinds of logic. To the left are two logic inputs and each gate has its own output. Remember, you can click on the inputs to change from...

Redtree Hydra: A modular platform for robotics
Instructions from Redtree Hydra: A modular platform for robotics
Share a SensorIf you want to see a complete example of sharing the sensor, check out the share a sensor app:svn co http://www.redtreerobotics.com/svn/redtree-apps/trunk/ redtree-apps cd redtree-apps/share_a_sensoror if you prefer git:git clone https://github.com/redtreerobotics/redtree-apps.git...

|<
<
1
2
3
4
5
>
>|