671 Results for "%E3%80%8A%EC%98%88%EC%95%BD%EB%B2%88%ED%98%B8OIOX8489X83O6%E3%80%8B%EA%B0%95%EB%82%A83hours%E2%80%BB%E2%82%84ours3hours%EB%A0%88%EA%B9%85%EC%8A%A4%E3%81%843hours%EB%A0%88%EA%B9%85%EC%8A%A43hours%E2%99%A3%E2%97%873hours%EB%A0%88%EA%B9%85%EC%8A%A4%EA%B0%80%EA%B2%A9linked 3hours%EB%A0%88%EA%B9%85%EC%8A%A4%E2%85%B73hours%EB%A0%88%EA%B9%85%EC%8A%A4%EA%B0%80%EA%B2%A9%E3%82%B9%E3%81%84status"

small micro speakers with a rich soundstage
Instructions from small micro speakers with a rich soundstage
print it, and once done remove all unneeded support materials., also please sand sharp corners down a bitnote: in this project Colorfabb NGEN was used for it's rigidness, but with only 10% infill note2: uploaded the models at 3Dhubs, since i don't have...

Airframe - Step 9
Instructions from MiniHawk VTOL
For each Nacelle with its respective Motor Mount aligned and present, Ream (Drill to size) using a 1.58mm (1/16 Inch, 62.5mil) drill bit. (Should be 85% to 90% of diameter of hinge rod to be fitted. Hinge Rod diameter is 1.84mm or 72mil for this case.)...

Schematics
Instructions from Compact Strain Gauge Board for MFE22
First, we need to make a schematic in Altium Designer or any other PCB design software. The schematic needs to be complemented by appropriately-sized components such as the INA818ID amplifier. Our board is powered by a low voltage 5V input. We used a...

Unruly signals: S.O.S....
Instructions from Open Source LiDAR - Unruly
SignalPinPortActionDescriptionRESETNJP4.14External reset control+3V3JP4.13Digital power lineAREFJP4.12Fixed at 3.3VHVIJP4.115V supply for laser and APDLASER_POWERJP4.10A0DACSet laser powerTHRESHOLDJP4.9A1DACComparator thresholdBIAS_VOLTAGEJP4.8A2ADCAPD...

Step 1: 3D printing
Instructions from UltraTower
To build a tower you will need to print the 3D parts shown on the left of the image. The "Sensors float" part is optional, print it if you want to use the pH and EC sensors. You will need 12 times the part: "Basket". You can download the files...

Step 1: 3D printing
Instructions from UltraTower 2023
To build a tower you will need to print the 3D parts shown on the left of the image. The "Sensors float" part is optional, print it if you want to use the pH and EC sensors. You will need 12 times the part: "Basket". You can download the files...

Arduino Game Console - the BlueOkiris Gameduino
Instructions from Arduino Game Console - the BlueOkiris Gameduino
Take the analog stick and solder the appropriate wires to it. Place ground to ground, 5v to 5v, x to A4, and y to A5. Again do not use male ends to the arduino.

Mona Lisa ParaFoil
Instructions from Mona Lisa ParaFoil
First you need to create a paper template. I used A4 white paper. I drew my lines for the angles of the wing shape on it. Including fold lines for the aerofoil shape.

Download it
Instructions from The AnyTop
The instruction set is available as PDF for A4 and US Letter size paper, as well as a ZIP archive of the raw images. It's in the FILES section...

ScrapTrack
Instructions from ScrapTrack
//. Motor driver shield- 2012 Copyright (c) Seeed Technology Inc. // // Original Author: Jimbo.we // Contribution: LG // // This library is free software; you can redistribute it and/or // modify it under the terms of the GNU Lesser General Public //...

ESP 8266 pin uses and restrictions
Instructions from ESP cookbook
Not all ESP 8266's GPIOs are born equal, something I have now and then been banging my head at (and burned some ESPs). Some are hard wired for some use, like SPI clock and data, some wired to functionality like flashing and booting. For now Wemos D1...

Instructions
Instructions from Budget DIY ESP32 GPS Base Station and Receiver
Best Budget DIY GPS/GNSS Base Station using the UM980 and a ESP32Introduction The ESP32 is a versatile microcontroller renowned for its WiFi and Bluetooth capabilities. In this guide, we’ll walk you through setting up the your ESP32 development board...

GCODE Commands
Instructions from DIY Inkjet Printer
The printer can be controlled by sending values via i2c. Each set bit represents a printer command like: 0 - everything off 1 - single drop printhead 1 2 - single drop printhead 2 4 - single drop printhead 3 8 - single drop printhead 4 16 - drops at...

Program the Arduino Microcontroller
Instructions from Simple Automated Model Railway Layout
Make sure to go through the program carefully to understand how it works, later it will be fun to tweak it and make your own modifications./* * Arduino program to control a model train running in a basic oval loop with the help of a feedback sensor....

Thanks!
Instructions from Smiley TOF Module
This project would not be anywhere near as complete without some awesome online resources and some awesome people. I would like to thank the devs at Adafruit for making some incredibly useful resources. I referred to the Metro Mini and VL53L0X product...

|<
<
3
4
5
6
7
>
>|