299 Results for "%EC%9E%A1%ED%86%A0%ED%86%A0%EB%94%94%EB%B9%84 %ED%85%94%EA%B7%B8%EB%9E%A8 DBmong %ED%86%A0%ED%86%A0abc %E1%92%A4 %EC%9E%A1%ED%86%A0%ED%86%A0%EC%82%AC%ED%96%89%EC%82%B0%EC%97%85 %ED%86%A0%ED%86%A0db%EC%B5%9C%EC%A0%80%EA%B0%80 %E1%92%A3 %EC%8B%A0%EC%9A%A9%EB%94%94%EB%B9%84%ED%8C%90%EB%A7%A4"

Appendix
Instructions from Carbon Intensity controlled Mains Socket Switch
Picking a value for a suitable carbon intensity to operate the switch is system dependent. As I have suggestedd I have a modern boiler that is probably about 85% efficient. A range of values for the amount of carbon dioxide equivalent releases...

Create a function to decode the payload
Instructions from 2022 HDP 4 - Climate Resilient Communities
In order to decode the 23 bytes of payload that the sensor is sending we need to implement a decoder, in this case we need to create one custom. Once you select to create a custom decoder you just simply copy and paste the next code which is written...

Affordable Reflectance Transformation Imaging Dome
Instructions from Affordable Reflectance Transformation Imaging Dome
Next step is to wire all the source leads on the MOSFETs together (the right lead when you're looking straight on at it), and also wire them to the one 2-pin female headers on the lower left side of the board (which will be connected to the positive...

Affordable Reflectance Transformation Imaging Dome
Instructions from Affordable Reflectance Transformation Imaging Dome
Time to start putting together the low-side driver board with the CAT4101s. First step is to install the connector on the 11 x 8.5 cm protoboard. This is the spec'ed component, but if you can't find one that size, you can use another one up to 11.5 cm...

Run a Program
Instructions from Digital Ammeter Using Arduino
#includeLiquidCrystal lcd (7,8,9,10,11,12); void setup() {// put your setup code here, to run once:Serial.begin(9600);lcd.begin(16,2);lcd.clear();} void loop() {// put your main code here, to run repeatedly:int voltage_value0 = analogRead(A0);int voltage_value1...

Adding video and sound cards to RC2014 aka RC2014+TMS+AY
Instructions from MSX on RC2014
In this step we will add the video module and optionally the sound module at that point you'll be able to run demos and games written specifically for this setup. Unless you want to run MSX BASIC or MSX games then you may want to stop there. RC2014 +...

Embedis : Keystore for Arduino Uno
Instructions from Embedis : Keystore for Arduino Uno
Air Quality SensorWe added the Air Quality Sensor to Analog Input A0 (Socket #1), in order to show how easy it is to add commands and do custom processing. Just enter the command : analogRead A0and you'll get the AiR quality reading from the sensor -...

Connecting the wires
Instructions from ZX Spectrum Expansion Port EEPROM Interface
ZX EEPROMMemrq -> oeA0-A13 -> A0-A13D0-D7 -> D0-D75v/gnd -> 5v/gndPull the eeprom we and a14 high. Connect the the zx a14 and a15 to pin 1 and 2 of the 74ls32 then pin 3 to ce pin of the eeprom. Also Connect the...

The sun-tracking system: to have the parabol always facing the sun
Instructions from The Sun Heater
The sun tracking system consists of: 1. Two roller shutter/awning motors: These motors are industrial, easy to purchase, cheap, and with a high torque (10Nm being the lowest). Average price of each motor around 30€...

Connect pin A0 to pin 11 on the Arduino board and click Acquire on the Arduscope web interface.
Instructions from Arduino oscilloscope with a web interface
You should see the 500Hz calibration signal displayed.

Counting Muscle Impulses
Instructions from Counting Muscle Impulses
Attach the SpikerShield to an ArduinoThe output of the SpikerShield is an analog value between 0 and 5 volts. It is connected to one of the Arduino's analog inputs. There is a jumper on the shield to determine which one. I keep mine on A0.

LinkTrucker
Instructions from LinkTrucker
Solder the +V pin from the Green LED on the RJ45 Ethernet connector.Connect this to A0 on the UNOYes - there IS possibly a way to do this in software, but I am a hardware hacker and this works great!

Home Control Center using BeagleBone Green Wireles
Instructions from Home Control Center using BeagleBone Green Wireles
STEP2: WIRINGI connect a Grove - Relay to GPIO_51, a Grove – Air quality sensor to A2 port and a Grove – Temperature sensor to A0 port on the Grove Base Cape for Beaglebone Cape.

Connect Sound Detector
Instructions from Cat Detector - Useless Machine
Use (3) jumper wires to connect the sound detector to the Arduino Uno (To the Wave Shield headers). 5V - VIN (Only do this if you are powering the Arduino at 5V with a USB cable), GND, AO - A0

Connect the Sensor to the Arduino Board
Instructions from Model Railway Layout With Automated Siding
Connect the VCC pin of the sensor to the 5-volt pin of the Arduino board, GND pin to GND pin of the Arduino board, and the OUT pin to the A0 pin of the Arduino board.

|<
<
3
4
5
6
7
>
>|