Close

465 Results for "e-ink"

  • Select you conductive material
  • Instructions     from WeavCoin - coin cell powered clothing
  • There are many ways to approach adding circuits to fabric.A common method is to use conductive tread to sew on or weave the circuits into fabric. You could also use conductive ink. However, there are known issues with longevity of such circuits.I wanted...

  • Preparing to print
  • Instructions     from Oasis 3DP
  • With Oasis built, wired, software running and a file prepared, it is time for the last step before printing, preparing the printer. This step mostly consists of properly filling the printer. Lower the feed piston by at least the amount you are going...

  • Tools and Materials
  • Instructions     from Custom PCB Using a Low Power Laser Engraver
  • The following tools and materials were used in this tutorial: 10W laser engraver (link / link / link). It was used for printing the circuit drawing on a blank copper PCB board. Copper PCB (link / link / link). Homemade circuit boards are usually printed...

  • Physical Build
  • Instructions     from SlimPi
  • The build is pretty straightforward: Attach the e-Paper display to the HAT using the supplied ribbon cablesAttach the e-Paper HAT to the GPIO headersAttach the e-Paper ribbon cable to the e-Paper displayFollow the SlimPi install instructions over...

  • Linkages/Components - Step 8
  • Instructions     from MiniHawk VTOL
  • Form the elevon control rods by creating an L-bend 45mm from the threaded tip of the pair of 2-56 link rods used. Test fit the retaining Du-Bro E/Z Links 0.72 (2-56) Retainer Clip for each bend, and modify the bend as needed and cut flush. Alternatively,...

  • Software Defined Vision System
  • Instructions     from Software Defined Vision System
  • 1 . O v e r v i e w This specification describes the procedure to write the following data to QSPI Flash and eMMC on Smart Vision Development Kit (SVDK). Data to be written to QSPI Flash: BOOT.binimage.ub.bin Data to be written to eMMC: rootfs_emms.tar.gzFirm.bin...

  • Multiroom Music Streaming
  • Instructions     from Multiroom Music Streaming
  • ssh into the server pi and run docker run --restart=always -d --net=host -e USER='YOUR SPOTIFY USERNAME' -e PASS='YOUR SPOTIFY PASSWORD' malted/mopidy-pulseaudio-serverReplace the USER and PASS values with your spotify credentials.The default login for...

  • Heatshrink JUUL to motor
  • Instructions     from Nicotine Vapour Exposure Chamber for Rats
  • Ensure your JUUL, or other compatible e-cigarette, is charged and filled with fluid. To seal the gap between the vacuum motor and the JUUL e-cigarette use a Heatshrink. Put a suitably sized Heatshrink around the end of the JUUL and the "IN" port of the...

  • Code Reference
  • Instructions     from AMB21/22/23 E-Paper Display Images
  • [1] We use Good Display GDEH029A1 2.9 Inch / 296×128 Resolution / Partial Refresh Arduino Sample Code to get the e-Paper successfully Display:http://www.good-display.com/product/201.html[2] Provide the link to how to generate a QR code on the E-paper...

  • Printing a part
  • Instructions     from Oasis 3DP
  • This step does not require much, since the printer does most of the work. Make sure the print area is prepared, the software is running and connected to both the motion driver and the printhead, and the file is loaded. There are 2 setting we are interested...

  • About the Project
  • Instructions     from DIY Inkjet Printer
  • In the following steps I will tell you how to build my DIY Inkjet Printer, but first I want to tell you a bit about this project. Back in 2019 after reading through the build logs of the Oasis 3DP I was searching on the internet if someone has ever tried...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday