1555 Results for "%E3%80%8A%20%EC%98%88%EC%95%BD%EB%AC%B8%EC%9D%98%20OIO%E2%89%A1%E2%91%A7%E2%91%A389%E2%89%A183O%E2%91%A5%E3%80%8B%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%EA%B2%AC%EC%A0%81%E3%82%88%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8ago%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%E3%83%A1%EA%B0%95%EB%82%A8%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8eighty%20%EC%84%A0%EB%A6%89%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%CE%BA%EC%84%A0%EB%A6%89%EB%A0%88%EA%B9%85%EC%8A%A4%E2%92%B2%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%E3%83%A1%EF%BD%83%EC%84%A0%EB%A6%89%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8literary"

Connect Sound Detector
Instructions from Cat Detector - Useless Machine
Use (3) jumper wires to connect the sound detector to the Arduino Uno (To the Wave Shield headers). 5V - VIN (Only do this if you are powering the Arduino at 5V with a USB cable), GND, AO - A0

Connect the Sensor to the Arduino Board
Instructions from Model Railway Layout With Automated Siding
Connect the VCC pin of the sensor to the 5-volt pin of the Arduino board, GND pin to GND pin of the Arduino board, and the OUT pin to the A0 pin of the Arduino board.

Run a Program
Instructions from Clap Switch with the help of Arduino
const int analogInPin = A0; // Analog input pin 0int sensorValue = 0; void setup() { DDRD = 0xFF;} void loop() { sensorValue = analogRead(analogInPin); //read ADC value on channel 0 if(sensorValue>60) { PORTD ^=(1<

Setting Up the Drone Transmitter
Instructions from DIY Radio Controller for Drone | nRF24L01
In this step, we will complete the Transmitter setup. We will do the circuit part first and after that, we will upload the code to the Arduino UNO to wrap up the setup. The materials required for this step are the NRF24L01 Transceiver module, Arduino...

Honeybee Hive Monitoring
Instructions from Honeybee Hive Monitoring
Add the HX711 sensor board to the Apitronics Bee.Connect the 4 wires from the scale to the 9-pin plug that passes through the weatherproof enclosure. These wires should be connected on the inside of the enclosure to E-, E+ (for excitation + and -) and...

Clone of stEve
Instructions from Clone of stEve
Breadboard circuit- The light follower circuit for the workshop is made up of two LDRs in voltage dividers with 22kOhm resistors (VCC - LDR - {signal to A0} - Resistor - Ground), (VCC - LDR - {signal to A1} - Resistor - Ground).- Additionally we supply...

RiseUp! System: Wheelchair Pressure Relief Monitor
Instructions from RiseUp! System: Wheelchair Pressure Relief Monitor
Connect FSRs, LED's to Ardunio Uno based on this fritzing diagram. Note: The "A0" pin is the analog pin which allows the FSR to communicate with the Ardunio Uno. More detailed step by step instructions for wiring will be posted for those that are just...

68000 Processor
Instructions from Nomad
Plug in the 68000 processor and minimal glue logic. To test if you build this part of the circuit correctly, add 10k pulldown resistors on all 15 data lines of the processor. Power on the board, and verify with an oscilloscope that A0 operates...

Assembly Steps
Instructions from Arduino Joystick Mouse
Print enclosure and file down inner tracks so that the joystick PCB slides in easily De-solder pins from joystick breakout board Use wires to make the following solder connections: Solder GND on Joystick to GND on Arduino Solder 5V on Joystick to VCC...

thingSoC I2C Hub
Instructions from thingSoC I2C Hub
The default address for the I2C hub is 0x74 with A2 shorted, and A1 and A0 Open.0 = Shorted, 1 = Open (ie. inverted...)A2 A1 A0 - I2C Address1 1 1 - 0x701 1 0 - 0x711 0 1 - 0x721 0 0 - 0x730 1 1 - 0x74 (Default I2C Address as shipped)0 1 0 - 0x750 0...

Uploading the code
Instructions from Arduino Controlled Safe (Locker)
*** FIRST DOWNLOAD AND INSTALL THE PASSWORD AND KEYPAD LIBRARIES *** JUST EXTRACT THEM IN ARDUINO LIBRARIES FOLDER Install the above mentioned two libraries. You can download them directly from the library manager or you can download the zip file and...

Run a Program
Instructions from IoT Digital Thermometer using LM35 and NodeMCU
#include const char* ssid = "*********"; // Your ssid const char* password = "***********"; // Your Password float temp_celsius = 0; float temp_fahrenheit = 0; WiFiServer server(80); void setup() { Serial.begin(115200); pinMode(A0, INPUT); Serial.println();...

Free run (optional)
Instructions from 68020 minimal homebrew computer
Although optional, it is highly recommended to test the board so far with the free run test. Connecting the databus to the ground, the CPU will read in 0x0000.0000 as an instruction and will execute a kind of NOP (in fact, it will execute ORI.b #0,D0)....

Reading pin voltages
Instructions from Wireless BLE Kinesis Advantage Keyboard (USB Host)
Ok, now we want to figure out the power states of our keyboard: Power On - normal batteryPower On - low batteryPower Off - ChargingPower Off - Battery Full So you'll need to read the BAT and USB pins on the Power Boost using the NRF52 ADC pins. The 5V...

ScrapTrack
Instructions from ScrapTrack
//. Motor driver shield- 2012 Copyright (c) Seeed Technology Inc. // // Original Author: Jimbo.we // Contribution: LG // // This library is free software; you can redistribute it and/or // modify it under the terms of the GNU Lesser General Public //...

|<
<
5
6
7
8
9
>
>|