Close

1464 Results for "%E3%80%8A%20%EC%98%88%EC%95%BD%EB%AC%B8%EC%9D%98%20OIO%E2%86%978489%E2%86%978306%E3%80%8B%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80%E2%94%A6%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80world%EC%84%A0%EB%A6%89%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80%EC%82%AC%EC%9D%B4%EC%A6%88%EC%B2%AD%EB%8B%B4%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80promotion%20%EC%84%A0%EB%A6%89%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80%E2%94%AB%20%E2%88%AB%EC%84%A0%EB%A6%89%EA%B0%80%EB%9D%BC%EC%98%A4%EC%BC%80decided"

  • Coil Gun
  • Instructions     from Coil Gun
  • Step 5- Putting it all together                                                             Silicone...

  • Writing a Protocol
  • Instructions     from StackMod: Modular Robotics Design Simplified
  • A big disclaimer to start with: I'm not an advanced developer/programmer -- I'm just an EE with a propensity for programming! This is also my first shot at writing a complete protocol so I'm sure there is quite a lot I'm missing but I approached this...

  • Coil Gun
  • Instructions     from Coil Gun
  • Step 4-Projectiles and testing of coil gun                                                        Coil gun projectileHere,...

  • Linkages/Components - Step 3
  • Instructions     from MiniHawk VTOL
  • The Motor Mount Tilt servos should be tested and centered on a standard RC PWM signal, visiting 1000us, 1500us, and 2000us pulse-widths. Attach a servo arm with a 19.3mm (0.76 Inch) hole-to-center spacing. This value is critical, as the linkage behavior...

  • Configure Raspberry Pi for Waveshare monitor
  • Instructions     from RUNBOX
  • In order to get the Waveshare to display properly you will need to edit the config.txt. To do so, open the terminal and type: sudo nano /boot/config.txt You will need to add the following: # 1920x1080 monitor (0 means monitor 1 the outside most hdmi...

  • The simplest 4-bit RISC CPU
  • Instructions     from The simplest 4-bit RISC CPU
  • Example of simple program for this CPU: Clear A accumulator, then continue add 1 to Accumulator register, until the value exceeds 15. Uses Add, Jump, and Jump when overflow instructions.Program EEPROM contentsAddress   instruction code...

  • IRK! Infrared Remote USB Keyboard
  • Instructions     from IRK! Infrared Remote USB Keyboard
  • Through Hole Technology (THT) versionThis is how I built the Through Hole Technology version Make a double-sided fibre glass PCB (see front- and back- PDF files below). There are several ways to do this. The way I do it is to print the front and back...

  • TFT LCD Displays - Setup and Testing
  • Instructions     from Greek Vocabulary Reviewer
  • For wiring the 3.5inch TFT LCD to Arduino UNO, please refer to the interface section in the WIKI. The resolution of these TFT LCD's is 480 x 320 (W x H). That is 480 pixels wide and 320 pixels tall if in landscape orientation or 320 pixels wide and 480...

  • Making the base and structure of piano
  • Instructions     from DIY Laser Piano
  • The base is made up of lot of cardboard ad glue gun. I have given the details along with the dimension in the image. Also make sure you are choosing the right kind of cardboard for making it. First Step: Marking, Cutting and Gluing base

  • Hardware of the sensor
  • Instructions     from Non-contact touch panel
  • Main board Main board pinout (JP1) pin numberPIN nameexplanation1+5VVcc 5V2GNDGND3ASensor channel 0bit4BSensor channel 1bit5CSensor channel 2bit6SSSPI Slave-Select (active-Low) Substrate selection when connecting in parallel.7MOSISPI Input8MISOSPI Output...

  • Lift kite
  • Instructions     from Energy Independence While Travelling
  • Let's start at the top with the lift kite An HQ KAP foil lift kite is a good steady lifter ... not so strong pulling as a single skin but stable. Practice with these so you are comfortable with their use before you attach one to a turbine. Make sure...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday