Results for %E3%80%8A%EC%98%88%EC%95%BD%EB%B2%88%ED%98%B8OIOX8489X83O6%E3%80%8B3hours%EB%A0%88%EA%B9%85%EC%8A%A4%EA%B0%80%EA%B2%A9%CF%803hours%ED%9B%84%EA%B8%B0wouldn't3hours%EB%A0%88%EA%B9%85%EC%8A%A4%EA%B0%95%EB%82%A83hours3hours%EB%A0%88%EA%B9%85%EC%8A%A4rosy 3hours%EA%B0%80%EA%B2%A9%E3%84%B4%E3%85%9E3hours%EB%A0%88%EA%B9%85%EC%8A%A4%EA%B0%80%EA%B2%A9addressing

Hacking a MG92b : Protect control bard
Instructions from Smarter Micro Servo (SMS) MOD
Use a a piece of heat-shrink sleeve as an envelop, or print a small 3D case to protect the control board.

Raspberry Pi Zero Smart Glass
Instructions from Raspberry Pi Zero Smart Glass
Next solder the ends of the smd buttons to the Pi Zero, and connect the camera cable to the Pi Zero

Raspberry Pi Zero Smart Glass
Instructions from Raspberry Pi Zero Smart Glass
Slide the Pi Zero through the PiHolder, with curved tweezers carefully guide the jst connecter and the camera cable through Buttonholder piece and the front bridge piece.

Arduino or Wemos Code
Instructions from WiFi Signal Strength Scanner Monitor or Checker
In the arduino code set your WiFi credentials char wifissid[] = "ENTER YOUR WiFi SSID HERE"; char wifipass[] = "ENTER YOUR WiFi PASSWORD HERE"; Normally, the signal strength is displayed in dBm. But for a non techie person, the signal strength in terms...

Trying out GATTTOOL
Instructions from Reading a bunch of BLE sensors with raspberryZero
Now that i know how to access and decode the data lets try the Raspi GATTTOOL default BLE handler:Native to Debian and a lso to a bunch of linux distros or so i've heard of . First i reset the bluetooth of the raspi, just in case: sudo service bluetooth...

RGB P4 Led Matrix Clock based on ESP32
Instructions from RGB P4 Led Matrix Clock based on ESP32
Schematics / AssemblySolder the elements on the printed circuit board according to the circuit diagram, instructions and markings placed on the printed circuit board.Connect the WeMos MiniID1 ESP-32, 16 pin male header using soldering or connectors.Insert...

Resource Monitor
Instructions from Resource Monitor
Solder wires from UBBB to LCD. (Note that uBBB pins are ordered as if looking at the bottom, since it also serves as a generic 32-TQFP breakout board if you flip it upside down). Specific connections are described below:-Connect pins 1, 5, and 16 on...

GCODE Commands
Instructions from DIY Inkjet Printer
The printer can be controlled by sending values via i2c. Each set bit represents a printer command like: 0 - everything off 1 - single drop printhead 1 2 - single drop printhead 2 4 - single drop printhead 3 8 - single drop printhead 4 16 - drops at...

EDID Inserter
Instructions from EDID Inserter
Plug in the freshly minted EDID Inserter and a repeated invocation of the following should yield only 256 FFs typical of an EEPROM fresh from the factory:sudo i2cdump 3 0x50Dire admonitions are issued even when merely trying to read:No size specified...

NODE-RED CONNECTIONS!
Instructions from OBS_IRL_STREAM_DECK
The first thing we need is a basic flow to separate button presses into different outputs. [{"id":"50b49ab2.1e6f64","type":"mqtt in","z":"7805686.aa4fd98","name":"","topic":"button_glove","qos":"0","datatype":"auto","broker":"","x":310,"y":2180,"wires":[["ea9f502f.2dd17"]]},{"id":"ea9f502f.2dd17","type":"json","z":"7805686.aa4fd98","name":"","property":"payload","action":"obj","pretty":false,"x":490,"y":2180,"wires":[["425aef92.aa3da8"]]},{"id":"425aef92.aa3da8","type":"function","z":"7805686.aa4fd98","name":"ButtonSeperator","func":"var...

Cuts required
Instructions from The Learner's Heliostat
The plywood product I used was 1/2x2x4 G1S, $37 ea before tax in Ontario in summer of 2022. For the project infrastructure, four 1" x 4" x 8' knotty pine planks would be price competitive and less work to waterproof, but less convenient to transport....

Rails
Instructions from Rave in a briefcase
I went for 2x3U. I screwed a piece of roofing battens into the case and the bottom rail directly onto them. The middle rails are just screwed together and are laid onto some standoff I laser cutted out of some scrap wood. The top rail...