1804 Results for "Q%20%EC%95%88%EC%82%B0%EB%B8%94%EB%9E%99%EC%9E%AD%20CDDC7_C%D0%9EM%20%E2%97%86%EB%B3%B4%EB%84%88%EC%8A%A4%EB%B2%88%ED%98%B8%20B77%E2%97%86%EC%88%98%EC%9B%90%EC%9E%A5%EC%95%88%20%ED%94%84%EB%A1%9C%ED%86%A0%20%EA%B5%AC%EB%A7%A4%E0%B9%8F%ED%86%A0%ED%86%A0%ED%95%AB%ED%94%BD%E2%8F%AC%EC%98%A8%EB%9D%BC%EC%9D%B8%ED%99%A9%EA%B8%88%EC%84%B1%E0%BC%88FX%EB%A7%A4%EB%A7%A4%E2%8B%8D%EC%95%88%EC%82%B0%EB%B8%94%EB%9E%99%EC%9E%AD%EC%95%A0%EC%9A%A9%20thorough/"
In the arduino code set your WiFi credentials char wifissid[] = "ENTER YOUR WiFi SSID HERE"; char wifipass[] = "ENTER YOUR WiFi PASSWORD HERE"; Normally, the signal strength is displayed in dBm. But for a non techie person, the signal strength in terms...
The main difference between the RFM modules is that they operate on different frequencies. As all the countries do not support the use of the same frequency band for free you need to used different module in different country. You can find about...
Now that i know how to access and decode the data lets try the Raspi GATTTOOL default BLE handler:Native to Debian and a lso to a bunch of linux distros or so i've heard of . First i reset the bluetooth of the raspi, just in case: sudo service bluetooth...
Flash the Arduino with the following sketch. This is also included as a file attached to the project. int last_level = 0; bool last_state = false; bool stable = false; int count = 0; const int cutoffs[198] = {/* 1*/ 833, 831, /* 2*/ 825, 823, /* 3*/...
The ESP-32 board pins operate in 3.3v levels while the Gravity pH and EC sensors operate in 5V. I inserted a simple voltage divider to shift 5v to 3.3v levels on the signal pins.
In order to control the video effects via MIDI, I needed a part that could override the potentiometers. For full effects, I need less than 30 ohms, to switch an effect off completely, a resistance of more than a few kohms would be desirable. I couldn't...
Below are the instructions given by the original lab that claimed to produce the room-temperature superconductor LK-99:- Prepare lanarkite (Pb2SO5) - PbO and PbSO4 mixed uniformly in a 1:1 molar ratio - bake in a...
Load the .bit file onto your Arty using Vivado. When the monitor starts, press L, then load the firmware s-record via your favourite terminal https://github.com/mattuna15/zed-68k/releases/tag/ARTY-100T-v1.0
Below are the steps that our lab followed during the first attempt of recreating LK-99:- Prepare lanarkite - weigh out roughly 1.7g PbO and 2.3g PbSO4 - mix until uniform in a clean beaker - transfer...
Components: Blue Robotics 4-core Ping Cable (11 metres), 2 x 4.5mm WLP-M06 cable wet link penetrators including nuts, o-rings, and silicone seal, plus 2 x cut shake-proof washers, 1 x rubber strain relief boot , 2 x Micro JST 2-way female connectors....
Hello...I have made the PrintrBot 1403 w/ a bed of 19.75" * 19.75" * 6" from a six inched cubed build environment. Now, that I am done w/ building that overweight beast of a printer, I have sort of moved on to a Monoprice Maker Select Plus...Since sort...