Close

6309 Results for "《 예약문의 OIO↗8489↗8306》선릉가라오케や가라오케추천received가라오케가라오케가라오케사이즈scarcely 청담가라오케иª가라오케사이즈glowing"

  • Initial Testing
  • Log     from Delta Printer - Capacitive Nozzle Probe
  • An Arduino ESP32 was setup using touchRead() in the main loop to toggle the onboard led and stream the read value out over Serial.  A single 15mm x 15mm x 1mm pad was tested with dial indicator to get a feel for the trigger range.  The led...

  • Side Project
  • Log     from Delta Printer - Capacitive Nozzle Probe
  • A digital bubble level was built to measure the platform tilt over the travel range.  This consists of an ESP32 dev board with 1.9" LCD and Sparkfun ICM-20948 breakout board.  The base was small enough to mount on the effector...

  • Mylar V2
  • Log     from Delta Printer - Capacitive Nozzle Probe
  • A Y-shaped section of black mylar was cut on the laser cutter with some holes to attached to clips printed from PLA.  A section of copper foil tape was placed in center of the Y for contact with the nozzle.  With the probe clipped onto the...

  • Bookworm and 1024x600 WIMAXIT screen
  • Log     from Portable Pi
  • The new version of the Raspberry Pi OS (Bookworm) as I mentioned above now uses Wayland rather than X. Consequently the config.txt hdmi commands recommended by WIMAXIT to configure their display for a Raspberry Pi no longer work. The display still...

  • The Basic Design
  • Log     from Lawnny Five
  • I’ve seen a lot of robotic lawnmowers over the years, but I wanted build something that was capable of more than just mowing the lawn— the ability swap different attachments for various jobs. Something more like a lawn tractor. The primary missions I’m...

  • Programmer/Debugging Board
  • Log     from Desktop Thermometer
  • While I am waiting for the boards to arrive, the time could be spent explaining the idea behind a separate programmer/debug board.  As mentioned in a previous post, there is no way of programming the microcontroller while it is installed on the...

  • Core Component Selection
  • Log     from Reflow Soldering Hotplate
  • MCU x CH552  STM32G031J6 (link): no USB, 8pin package STM32F042F4 (Link): USB2.0, 1x 12bit ADC Temperature Sensors PT100(ADC)P0K1.232.6W.Y.010€ 6.08/ 1€ 3,32/ 1kuPT100(ADC)PTFC101B1G0(datasheet)€ 2,81/ 1€ 1,34/ 1kuThermistor(ADC)NTCLE203E3104GB0A(datasheet)€...

  • Original article OCR
  • Log     from NS 32000 cross-assembler in C
  • Dr. Dobb’s Journal, December 1986, page 48. A table-driven assembler that can be modified for other processors. Series 32000 Cross-Assembler by Richard Rodman, 1923 Anderson Rd., Falls Church, VA 22043 The 32000 processor features generalized addressing...

  • First version
  • Log     from Arduino shield 4-digit 7-segment LED Display
  • 4-digit display shield build on the Proto board.See Fig.1. Parts List: 1. Arduino Uno R3 2.HiLetgo R3 Proto Shield Proto Expansion Board 3. 4-digit 7-segment LED display module     Model: 5641AS ,  Size: 0.56 x 1.98 inch ,  Emitting...

  • Measure twice or thrice or....
  • Log     from The Tile Job
  • In this project log entry, I'm recording various measurements so as to have them all in one place instead of the zoo of tiny slips of paper where I have previously recorded them. Some measurements will only be determined after I have done some demolition,...

  • Tile selection
  • Log     from The Tile Job
  • Looking at available tiles is dizzying. There are several different materials, several common sizes, and unaccountably many colors or patterns. If it were easy or inexpensive to change out the tiles, I'd probably go with something pretty provocative...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday