Close

22780 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 강남쓰리아워F グpossibility쓰리아워┃쓰리아워가격쓰리아워레깅스룸Iシ쓰리아워레깅스룸unnatural 쓰리아워ы쓰리아워레깅스룸㏅㈇temper"

  • Project Log 64: DIY Linear Actuator.¹

  • 21/07/2023, Friday, 10:16. For some reason this last week got me too lazy to do anything at all... Well, I will just leave this here and see what I can think of... ----------------------------------------------------------------------------------------------------------...
  • Clean Jack Screw.

  • (update 2017-5-23) Here's prototype 2, (maybe 2.5) with the clean jack screw installed. The nut retention leaves a lot to be desired, it was hacked from piece of brass early morning in a hotel room. (yes, I cleaned up the little sharp nibblings.) Works...
  • Iron man suit overview

  • With energy, there are multiple things to look at when choosing materials. The main thing to look at for today is PSI and heat resistance. The material I choose will need a high level of both. This is due to the way the reactor works. After searching...
  • Frequencies

  • For some reason the 47 pF value for the caps is sitting in my mind. Either after 'calibration' the LC meter is so far off that it read both my TI-89's and my V200's caps 51 pf, both ~8% high, or both of them are within their 10% tolerance and reading...
  • Parity with Fibonacci

  • One thing that sets PEAC apart from the Fibonacci and Pisano series is the parity, or mod 2 remainder. When you take the natural sequence 0, 1, 1, 2, 3, 5, 8, 13, 21, 34, 55, 89, 144, 233, 377, 610, 987, 1597... The mod 2 is 0, 1, 1, 0, 1, 1, 0, 1, 1,...
  • Finally, some publicity!

  • An article recently published on MOONGIFT, a Japanese developer site, has showcased RasDash! The article is entirely in Japanese and Google Translate won't accept the URL as it has special characters but YANDEX does. Below are some links and a basic...
  • It's like being in college again.

  • Mid-day update: April 20, 89 PDWhile over 75% of the internal parts are finished printing, but there is still too much to do. We have started wiring up the reactor with LEDs but it is slow going (25% done). We have not even started on the code to drive...
  • MORE RADII!!

  • I haven't putzed about with the v0.1 base at all, but I think I've got a motor mount design that I like. It's got the split bolt setup for securing the motor (including a cutout for holding a 2-56 nut), and the legs are cool lofted dealies. Lots of radii...
  • Fibonacci

  • With the ALU verified and the RAM connected, today the breadboard determined that the first 8-bit Fibonacci number is 144. 0000 0000 ld $00 ; outer loop 0001 c200 st [$00] ; a=0 0002 0001 ld $01 ; b=1 0003 fc0a bra $0a 0004 0200 nop ; (pipelining) 0005...
  • Housing selection

  • Requirements Easily found when misplacedBig enough to hold easily but not too big that it's cumbersomeShould have a battery compartment so that unskilled personnel can replace batteries without having to open up the housingRoom enough for the necessary...
  • MIKBUG Commands

  • MIKBUG (Smithbug) has the following case-sensitive commands. ; V VIEW MEMORY; E CHANGE MEMORY; M MOVE MEMORY; I FILL MEMORY; F FIND  ; D DISASSEMBLE CODE; & S1 LOAD PROGRAMME; G GO TO PROGRAM; J JUMP TO TARGET PROGRAM ; T TRACE PROGRAM; K CONTINUE...
  • FlexSEA-Plan

  • FlexSEA-Plan is an embedded computer used for high-level computing. It boasts a powerful processor and can run an operating system such as Linux. Developing code on this platform is similar to the regular (i.e. non-embedded) software development process....
  • All Your ISA Belong to Me!

  • Before I began the layout of the DDL4-CPU, I came up with an initial Instruction Set Architecture (ISA) for the design. It went through several revisions as I was designing the boards and refined the components. Here at the last minute as I am...